Filter
Top Products
i
Certification
Agilent Technologies certifies that this
product met its published specifications at the
time of shipment from the factory. Agilent
Technologies further certifies that its
calibration measurements are traceable to the
United States National Institute of Standards
and Technology (formerly National Bureau of
Standards), to the extent allowed by that
organization’s calibration facility, and to the
calibration facilities of other International
Standards Organization members.
Additional Information for Test and
Measurement Equipment
To comply with EMC regulations, shielded
cables should be used on all appropriate
connections. Otherwise, the user has to
ensure that, under operating conditions, the
Radio Interference Limits are still met at the
border of the user's premises.
Warnings
The following general safety precautions
must be observed during all phases of
operation, service, and repair of this product.
Failure to comply with these precautions or
with specific warnings elsewhere in this
manual violates safety standards of design,
manufacture, and intended use of the
product. Agilent Technologies assumes no
liability for the customer’s failure to comply
with these requirements.
Ground the Equipment
Ground the EquipmentGround the Equipment
Ground the Equipment: For safety, Class 1
equipment (equipment having a protective
earth terminal), an uninterruptible safety
ground must be provided from the mains
power source to the product input wiring
terminals or supplied power cable. Before
operating the equipment, guard against
electric shock in case of fault by always using
the provided 3-conductor power cord to
connect the equipment to a grounded power
outlet.
DO NOT use in hazardous environments
DO NOT use in hazardous environmentsDO NOT use in hazardous environments
DO NOT use in hazardous environments: Do
not operate the product in an explosive
atmosphere or in the presence of flammable
gases or fumes. This product is designed for
indoor use only.
DO NOT use repaired fuses or short-circuited
DO NOT use repaired fuses or short-circuited DO NOT use repaired fuses or short-circuited
DO NOT use repaired fuses or short-circuited
fuse holders
fuse holdersfuse holders
fuse holders: For continued protection against
fire, replace line fuses only with fuses of the
same voltage and current rating and type.
Keep away from live circuits
Keep away from live circuitsKeep away from live circuits
Keep away from live circuits: Operating
personnel must not remove equipment covers
or shields. Procedures involving the removal
of covers and shields are for use by service-
trained personnel only. Under certain
conditions, dangerous voltages may exist
even with the equipment switched off. To
avoid dangerous electrical shock, DO NOT
perform procedures involving cover or shield
removal unless you are qualified to do so.
DO NOT operate damaged equipment
DO NOT operate damaged equipmentDO NOT operate damaged equipment
DO NOT operate damaged equipment:
Whenever it is possible that the safety
protection features built into this product
have been impaired, either through physical
damage, excessive moisture, or any other
reason, REMOVE POWER and do not use the
product until safe operation can be verified by
service-trained personnel. If necessary, return
the product to an Agilent Technologies Sales
and Service Office for service and repair to
ensure the safety features are maintained.
DO NOT substitute parts or modify
DO NOT substitute parts or modify DO NOT substitute parts or modify
DO NOT substitute parts or modify
equipment
equipmentequipment
equipment: Because of the danger of
introducing additional hazards, do not install
substitute parts or perform any unauthorized
modification to the product. Return the
product to an Agilent Technologies Sales and
Service Office for service and repair to ensure
features are maintained.
DO NOT clean with fluids
DO NOT clean with fluidsDO NOT clean with fluids
DO NOT clean with fluids: Doing so may
make the equipment unsafe for use. Power
down the equipment and disconnect the
power cord before cleaning. To clean, use a
soft dry cloth.
Safety Symbols
If you see this symbol on a product, you must
refer to the manuals for specific Warning or
Caution information to avoid personal injury
or damage to the product
Indicates the field wiring terminal that must
be connected to ground before operating the
equipment. Protects against electrical shock
in case of fault.
Frame or chassis ground terminal. Typically
connects to the equipment’s metal frame.
Alternating current (ac).
Direct current (dc).
Indicates hazardous voltages and potential for
electrical shock.
Indicates that antistatic precautions should be
taken.
This product complies with CSA requirement
CSA 22.2 No. 1010.1, NRTL/C, EN 61010-
1:1993 + A2:1995/IEC 1010-1:1990 +
A1:1992 + A2:1995 Safety requirements for
electrical equipment for measurement,
control, and laboratory use.
Notice for European Community: This product
complies with the relevant European legal
Directives: EMC Directive 89/336/EEC and
Low Voltage Directive 73/23/EEC.
Das CE-Zeichen zeigt die Übereinstimmung
mit allen für das Produkt geltenden Direktiven
der Europäischen Union an.
This is the symbol for an Industrial, Scientific,
and Medical Group 1 Class A product.
or
ISM 1—A