Aube Technologies TI073 Switch User Manual


 
TI073 400-073-000-A 2009-01-28 1/2
The TI073 programmable wall switch can be used in a single-switch or 3-way installation with the following
types of lighting:
The TI073 switch cannot be used with a load of less than 40 W or more than 500 W.
n Cut power at the circuit breaker to avoid electric shock.
o Remove the existing switch. (For a 3-way installation, identify and label the wire connected to the
“common” screw.)
p Install the new switch (see the appropriate section below).
q Apply power at the circuit breaker.
WARNING: Disconnect power to the switch when replacing a light bulb (see section 4).
SINGLE-SWITCH INSTALLATION
Connect the LINE and 3-WAY wires to the line (120 V) wire and LOAD wire to the load. Connect the GND
wire to a ground screw inside the electrical box.
EXISTING 3-WAY INSTALLATION
Connect the LOAD wire on the TI073 to the “common” wire, which you identified when removing the old
switch. Connect the GND wire to a ground screw inside the electrical box. Connect the LINE and 3-WAY
wires to the two remaining wires. At the other 3-way switch, connect the jumper wire between the “common”
screw and the screw where the LINE wire of the TI073 is connected.
NEW 3-WAY INSTALLATION
The TI073 will turn the lights on at sunset and turn them off at 11:00 pm by default. If these settings are
appropriate for you, you only need to set the time and date (see shaded zone in the menu flowchart sheet).
If the switch’s sunset time does not correspond to the actual sunset time, see sections 5.3.3 and 5.3.4.
5.1 Mode Menu
Use the Mode menu to select one of the three modes of operation (see sections 5.1.1 to 5.1.3).
5.1.1 Manual Mode
In Manual mode, the TI073 operates like a regular switch. To turn the lights on or off, briefly
press the main button. The icon appears when the switch is in Manual mode.
5.1.2 Automatic Mode
In Automatic mode, the TI073 turns the lights on or off according to the set programs (see
Section 5.4). The icon as well as the current program number are displayed.
5.1.3 Random Mode
In Random mode, the TI073 has no specific times to turn the lights on or off. This mode is
designed to give the impression the house is occupied during your absence. It is similar to
the Automatic mode except there is no fixed program. The programs are automatically set
to different times by the TI073 every day. The icon appears when the switch is in
Random mode.
The first “On” program occurs at sunset. Each “On” program lasts between 1 hour and 1
hour and 30 minutes; each “Off” program lasts between 15 and 30 minutes. The last “Off”
program occurs between 10:30 pm and midnight.
5.1.4 Temporary Override
When the TI073 is in Automatic or Random mode, you can press the main button at any time to override the
default state for the current program. The lights will turn off if they are on and vice versa. The new state icon
(On or Off) flashes to indicate that the state is temporary. The new state is maintained until you press the
main button again or till the next “On” or “Off” program.
n
Applications
1.
• Incandescent • Halogen • Low-voltage halogen with transformer • Fluorescent
o
Installation
2.
black
white
black (LINE)
black (LOAD)
green (GND)
yellow (3-WAY)
120
VAC
120
VAC
black
white
black
white
black
white
black (LINE)
black (LOAD)
green (GND)
yellow (3-WAY)
120
VAC
jumper
three-way
switch
black (LINE)
black (LOAD)
green (GND)
yellow (3-WAY)
black
white
black
white
black
white
red
120
VAC
black (LINE)
black (LOAD)
green (GND)
yellow (3 WAY)
single-pole
switch
black
white
black
white
white
black
p
Quick Start-up
3.
Set the time and date before using the switch for the first time.
q
Operation
4.
r
Setup Menus
5.
Press the main button for 3 seconds to enter the setup menus. Refer to
the menu flowchart sheet on how to navigate the menus.
The icon indicates the current program
has been activated at sunset.
The icon indicates the current program
has been activated at sunrise.
The LED illuminates when the load state is on.
Briefly press this button to turn the
lights on or off. See “Temporary
Override” in Section 5.1.4.
Press for 3 seconds to enter the
setup menus.
Indicates the mode of
operation (see Section 5.1)
Indicates the current program
Press this button to display today’s sunrise time.
Press this button to display today’s sunset time.
Safety switch
Before replacing a light bulb, pull out to disconnect power to the switch.
This prevents, while the bulb is out, any possible short circuit which will
damage the switch. Push back in after the light bulb is replaced.
Indicates the load on/off state
Indicates the time and day
(3 sec.)
TI073
User guide
7-day Solar Programmable Wall Switch
400-073-000-A ENG.fm Page 1 Wednesday, January 28, 2009 9:41 AM