Filter
Top Products
122
E
Error
code
Message Meaning Action
E001
Wrong mode
Mode switch position changed before fi nalization. Return the mode switch to its original setting and fi nalize
the operation.
E003
Wrong operator
Clerk button pressed before fi nalization of a registration
being performed under another clerk button.
The signed on clerk differs from the clerk performed the
tracking check registration.
Press the original clerk button and fi nalize the transaction
before pressing another clerk button.
Input correct check number or assign the proper clerk
number.
E004
Error INIT/FC
Initialization or unit lock clear operation in progress. Complete operation.
E005
Insuffi cient memory
Memory allocation exceeds total memory capacity. Reallocate memory or expand memory (if possible).
E008
Please sign on
Registration without entering a clerk number. Enter a clerk number.
E009
Enter password
Operation without entering the password. Enter password.
E016
Change back to REG
mode
Two consecutive transactions attempted in the refund
mode.
Switch to another mode and then back to the RF mode for
the next transaction.
E017
Enter CHK/TBL
number
Attempt made to register an item without inputting a
check number.
Input a check number.
E018
Enter Table number
Attempt made to register an item without inputting a table
number.
Input a table number.
E019
Enter number of
customers
Finalize operation attempted without entering the number
of customer.
Enter the number of customer.
E021
No DEPT Link
No department linked PLU is registered. Correct the program.
E023
Stock shortage
Actual stock quantity becomes less than the minimum
stock quantity.
Perform stock maintenance.
E024
No stock
Actual stock quantity becomes / is negative. Perform stock maintenance.
E025
Illegal scale read
or entry
Scale reading error or Manual entry for scalable item. Put item on the scale again or do not enter weight by
hand.
E026
Enter condiment/
preparation PLU
No condiment / preparation PLU is registered. Register condiment / preparation PLU.
E029
In the tender
operation
Item registration is prohibited, while partial tender. Finalize the transaction.
E030
Press RATE TAX key
Finalization of a transaction attempted without register-
ing rate-tax.
Register <RATE TAX>.
E031
Press ST key
Finalization of a transaction attempted without confi rm-
ing the subtotal.
Press <SUBTOTAL>.
E032
Press FSST key
Finalization of a transaction attempted without confi rm-
ing of the food stamp subtotal.
Press <FS/ST>.
E033
Enter tendered
amount
Finalize operation attempted without entering amount
tender.
Enter the amount tendered.
E035
Change amount
exceeds limit
Change amount exceeds preset limit. Input amount tendered again.
E036
Remove money from
the drawer
Contents of the drawer exceed programmed limit. Perform pick up operation.
E037
Digit or amount
limitation over
High amount lock out / low digit lock out error Enter correct amount.
E038
Perform money
declaration
Read / reset operation without declaring cash in drawer.
This error appears only when this function is activated.
Perform money declaration.
E040
Issue guest receipt
Attempt to register a new transaction without issuing a
guest receipt.
Issue a guest receipt.
E041
Print validation
Attempt to register a new transaction without validation.
Perform validation operation.
E042
Insert VLD paper
and retry
Validation paper (slip printer) has run out. Insert new validation paper.
E044
Print Cheque
Attempt to register a new transaction without printing check.
Perform check print.
E045
Print Check
Endorsement
Attempt to register a new transaction without printing
check endorsement.
Perform check endorsement.
E046
REG buffer full
Registration buffer full. Finalize the transaction.
E047
Print bill
Separate check buffer full. Allocate suffi cient separate check buffer.
E048
Insert slip paper
and retry
Attempt to register a new transaction without printing slip.
No paper is inserted or paper is out in the slip printer.
Perform slip printing operation.
Insert new slip paper.
E049
CHECK memory full
Check tracking index memory full. Finalize and close the check number currently used.
E050
DETAIL memory full
Check tracking detail memory full. Finalize and close the check number currently used.
This section describes what to do when you have problems with operation.
Troubleshooting
When an error occurs
Errors are indicated by an error codes. When this happens, you can usually fi nd out what the problem is as illus-
trated below.
Press
C
and check the appropriate section of this manual for the operation you want to perform.