Filter
Top Products
Chapter 3: Setting up the Printer 25
A760-D100 10/04 189-9200303 Rev. D A760 Two-Color Thermal/Impact Hybrid Printer: User Guide
*** A760 - Diagnostics Form ***
*** A760 - Diagnostics Form ***
Model number : A760-1125
Serial number : A012451679
Boot Firmware
Revision : V1.03
CRC : FFDE
P/N : 189-7600118A
Flash Firmware
Revision : V1.05
CRC : 7196
P/N : 189-7600117A
H/W parameters
Flash Memory Size : 1 Mbyte
Flash Logos/Fonts : 320 kbytes
Flash User Storage : 0 kbytes
SRAM Size : 256 kbytes
Head setting : D
Paper Type Name : Type 1, Version 0
Color Density Adj : 100 %
Print Density (Mono) : 100 %
Max Speed : 100 mm/sec
Max Power : 55 W
Alternate Reset : Disabled
Knife : Enabled
Paper Low Sensor : Enabled
MICR : Enabled
MICR Dual Pass : Disabled
MICR DC offset : 80
Check Flip : Enabled
Comm. Interface
RX Buffer Size : 4096
Interface type : RS232/USB
Parameters
Baud Rate : 115200
Data Bits : 8
Stop Bit : 1
Parity : NONE
Flow Control : DTR/DSR
Reception Errors : Ignore
Alternate DTR/DSR : Disabled
Resident Code Pages : 437, 850, 852. 858
860, 863, 865, 866
1252,862, 737
Available Paper Types :
00.00 01.00 05.00
Logo(s) defined : YES
User Char(s) defined : NO
To enter Printer Config Menu :
1) Flip DIP switch #1 up
2) Reset the printer, while holding
the Paper Feed button down
***
***
A760 - Printer Config Menu
A760 - Printer Config Menu
***
***
This config menu allows you to set general printer
parameters
Sub-menus are entered and selections are made using
the Paper Feed Button
- short click : Feed Button is quickly depressed
then released
- long click : Feed Button is held down more than
1 second then released
CAUTION !!
CAUTION !!
The settings are predetermined in factory and
should generally not be changed.
If you must change the settings do so carefully
to avoid changing other functions.
****************
********
MAIN MENU
MAIN MENU
********
**************************
Select a sub-menu :
- EXIT -> 1 click
- Print Current Configuration -> 2 clicks
- Set Communication Interface -> 3 clicks
- Set Diagnostics Modes -> 4 clicks
- Set Emulation/Software Options -> 5 clicks
- Set Hardware Options -> 6 clicks
- Set Paper Type -> 7 clicks
Enter code, then hold Button DOWN
at least 1 second to validate
Important: Ensure that the
configuration settings match
your host computer, if not,
enter the configuration menu
to make changes.
}
Current printer tallies are
printed after the diagnostic
information and will vary
per printer use.
Sample diagnostic menu and print test for serial connection(show approximately 60% of size). Ethernet diagnostic
printout not shown. Ethernet parameters can not be changed in the configuration menu.
When the printer is configured
for USB and the native USB
solution driver is used, this
location will show either: “USB
Driver Type: TPG, Inc.” or “USB
Driver Type: Printer Class”.
If the RS-232C, USB emulation
solution driver is used, nothing
is printed here. See User Guide,
Appendix A.
Paper type can be changed
in the configuration menu.
Paper types and grades
available:
Type 0 - Monochrome grades
Kanzaki P-310
Type 1 - Two-color grades
Kanzaki P-310 RB
Type 4 - Two-color grades
Kanzaki P-310 BB
Type 5 - Two-color grades
Kanzaki P-320 RB
See page 48 and Programming
guide for more information.