Filter
Top Products
SNMP / SERIAL PORT
CARD OPTION KIT
4. Remove the Serial Port Card located on the rear of the UPS.
3. Disconnect all devices connected to the UPS receptacles and unplug
the UPS.
5. Install the SNMP / Serial Port Card. Take care to seat it properly.
NOTICE
The information in this publication is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR
TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN,
NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. THIS
INFORMATION IS PROVIDED “AS IS” AND COMPAQ COMPUTER
CORPORATION DISCLAIMS ANY WARRANTIES, EXPRESS, IMPLIED OR
STATUTORY AND EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, GOOD TITLE
AND AGAINST INFRINGEMENT.
This publication contains information protected by copyright. No part of
this publication may be photocopied or reproduced in any form without
prior written consent from Compaq Computer Corporation.
© 2000 Compaq Computer Corporation
Compaq, Compaq Insight Manager, SmartStart
Registered U.S. Patent and Trademark Office.
COMPAQ SNMP / SERIAL PORT CARD OPTION KIT
QUICK INSTALLATION GUIDE
Second Edition (November 2000)
Part Number 201544-022
Compaq Computer Corporation
Printed on recycled paper
Open Guide Completely Before
Beginning Installation Procedures
Quick Installation Guide
This guide serves as an outline to assist qualified personnel with the
installation of the Compaq SNMP / Serial Port Card.
About This Device
NOTE: The rating label on the device provides the class (A or B) of the
equipment. Class B devices have a Federal Communications Commission (FCC)
logo or identification (ID) number on the label. Class A devices do not have an
FCC logo or ID on the label. After you determine the class of the device, refer to
the appropriate UPS Operation and Reference Guide section of the Power
Products Documentation CD for complete regulatory compliance notices.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS - This Quick Installation Guide contains
important instructions that should be followed during installation and
maintenance of the UPS option.
Please refer to the Important Safety Information (included in your UPS
Kit) before installing this product.
Important Safety Information
Read Before Installing Product
WARNING: There is a risk of personal injury from electrical shock
and hazardous energy levels. The installation of options and routine
maintenance and service of this product must be performed by
individuals who are knowledgeable about the procedures,
precautions, and hazards associated with AC Power Products.
System Compatibility
The Compaq SNMP / Serial Port Card can be used with all Compaq
UPS XR Uninterruptible Power System (UPS) models.
Installation
WARNING: To reduce the risk of personal injury from electric shock,
disconnect all loads from the UPS receptacles before unplugging the
UPS. Avoid operating the UPS while it is disconnected from the
source of electrical power.
Identifying the Contents of the Option Kit
The SNMP / Serial Port Card Option Kit contains the following items:
1
SNMP / Serial Port Card
Configuration cable (Compaq part number 291092-002)
Compaq Power Products Documentation CD containing the:
Compaq SNMP / Serial Port Card Reference Guide
Compaq Power Products Software Reference Guide
Compaq power management communication software CD
You will also need to provide your own #2 Phillips screwdriver.
Installing Compaq Power Management
Communcations Software
Install the Compaq power management communication software
following the instructions included in the SNMP / Serial Port Card
Option Kit.
2
1
IOIOI
10
Compaq SNMP / Serial Port Card
Installation is Complete.
Before the SNMP / Serial Port Card can be configured, Compaq
power management communication software must be installed on
every server or workstation protected by the host UPS. To install the
software, please refer to the "Configuration" section of the
SNMP / Serial Port Card Reference Guide (included on the Power
Products Documentation CD).
For information on operating the SNMP / Serial Port Card, please
refer to the "Operation" section of the power management
communication software guide (included on the Power Products
Documentation CD).
Use the Compaq website as an additional information source by
logging onto the Internet at www.compaq.com.
Ethernet network cable RJ-45 connector on SNMP / Serial Port Card
Server
Power
Communications
UPS
Network
Device
1
2
Configuring the SNMP / Serial Port Card
Configure the SNMP / Serial Port Card using the instructions in the
Compaq SNMP / Serial Port Card Reference Guide (provided on the
Power Products Documentation CD).
6
Reconnecting All Devices
Reconnect network devices to the UPS and power up the UPS.
Connecting to Network
Plug one end of an Ethernet network cable ( ) into the RJ-45 connector ( )
on the SNMP / Serial Port Card. Plug the other end into an appropriate port
on your network device.
4
5
Installing the SNMP / Serial Port Card
1. Perform a normal system shutdown on all devices connected to the
host UPS in which you are installing the SNMP / Serial Port Card.
2. Place the UPS in Standby mode (from Operate mode or Configure
mode) by pressing the STANDBY button ( ) as shown below.
3
Compaq SNMP / Serial Port Card
IOIOI
10
201544- 022