Dell 0476T Computer Monitor User Manual


  Open as PDF
of 2
 
®
Observe the following safety guidelines when connecting and using your monitor:
•Be sure your monitor is electrically rated to operate with the AC power available in your location.
•Locate your monitor near an easily accessible electrical outlet.
•Place the monitor on a solid surface and treat it carefully. The screen can be damaged if dropped, sharply hit, or touched with a sharp or abrasive implement.
•Put your monitor in a location with low humidity and a minimum of dust.
•Never use your monitor if the power cable has been damaged. Do not allow anything to rest on the power cable, and keep the cable away from where people could trip over it.
•Never insert anything metallic into the monitor openings. Doing so may create the danger of electric shock.
•To avoid electric shock, never touch the inside of the monitor. Only a qualified technician should open the monitor's case.
•Be sure to hold the plug, not the cable, when disconnecting the monitor from an electrical outlet.
•Openings in the monitor cabinet are provided for ventilation. To prevent overheating, these openings should not be blocked or covered. Also, avoid using the monitor on a bed,
sofa, rug, or other soft surface. Doing so may block the ventilation openings in the bottom of the cabinet. If you put the monitor in a bookcase or some other enclosed space, be
sure to provide adequate ventilation.
•Do not expose the monitor to rain or use it near water. If the monitor accidentally gets wet, unplug it and contact an authorized dealer immediately. You can clean the exterior of
the monitor with a damp cloth when necessary, but be sure to unplug the monitor first.
•If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or ser-
vice center.
1. Turn off your computer and unplug the computer power cable.
2. Connect the blue connector of the monitor’s signal cable to the blue video connector on the back of your computer. Tighten the connector screws finger tight. Do not
overtighten.
3. Fully insert the monitor power cable into the power port on the back of the monitor.
4. Plug the power cables of your computer and your monitor into a nearby electrical outlet.
5. Turn on your computer and monitor. If the monitor does not display an image, refer to the troubleshooting section of this guide.
Use the monitor CD to install the appropriate monitor driver for your operating system.
Microsoft Windows
®
98 Operating System
Windows 98 automatically detects the new monitor and displays the
Add New
Hardware Wizard
dialog box if the monitor driver is not already installed.
1. Insert the monitor CD in the CD-ROM drive, and click
next>
twice when the
Add
New Hardware Wizard
dialog box appears.
2. Click the
CD-ROM drive
box to install the drivers from the CD and then click
Next>
.
3. Confirm that the driver was found on the CD and click
Next>
twice to install the
driver.
4. Click
Finish
to exit the add
New Hardware Wizard
dialog box.
To manually install or update the driver, perform the following steps:
1. Click
Start-> Settings-> Control Panel
and then double click
Display
.
2. In the
Display Properties
window, click the
Settings
tab, and then click
Advanced
.
3. Click the
Monitor
tab, and then click
Change
.
4. When the
Update Device Driver Wizard
dialog box appears, follow the steps in the
previous paragraph.
Microsoft Windows
®
95 Operating System
First determine the Windows 95 version installed on your computer by right-clicking the
My Computer
icon on the desktop and selecting
Properties
. The version number is
listed under
System
. Perform the steps for the appropriate version.
Version 4.00.950A
1. Click
Start-> Settings-> Control Panel
and then double-click
Display.
2. In the
Display
Properties
window, click the
Settings
tab and the click
Change
Display
Type
.
3. In the
Change
Display
Type
window, click
Change
and then click
Have
Disk
.
4. Insert the monitor CD in the CD-ROM drive, type d:\ (change the drive letter to
match your CD-ROM drive if it is not drive D) in the
Copy
manufacturer’s
files
from
: box, and click
OK
.
5. In the
Select
Device
window, click the appropriate monitor model and the click
OK
.
6. In the
Change
Display
Type
window, click
Close
.
7. In the
Display
Properties
window, click
OK
.
Version 4.00.950B
1. Click
Start-> Settings-> Control Panel
and then double-click
Display
.
2. In the
Display Properties
window, click the
Settings
tab and the click
Advanced
Properties
.
3. In the
Advanced Display Properties
window, click the
Monitor
tab and then click
Change
.
4. In the
Select
Device
window, click
Have
Disk
.
5. Insert the monitor CD in the CD-ROM drive, type d:\ (change the drive letter to
match you CD-ROM drive if it is not drive D) in the
Copy
manufacturer’s files from
:
box, and click
OK
.
6. In the
Select Device
window, click the appropriate monitor model and then click
OK
.
7. In the
Advanced Display Properties
window, click
Close
.
8. In the
Display
Properties
window, click
OK
.
Safety Instructions
Driver Installation
Connecting Your Monitor to a Computer
Dell
®
Model UltraScan P991 Color Monitor Quick Setup