Filter
Top Products
Warning
Please read this instruction carefully before use.
Switch off the power before wiring.
The display panel of TP05G and TP08G is waterproof. But please prevent grease, corrosive liquids and sharp
objects from contacting the TP05G and TP08G.
The TP05G and TP08G require 24VDC input power. DO NOT connect input AC power supply to any of the RS-485
communication port; otherwise serious damage may occur. Check all the wiring again before switching on the
power.
DO NOT touch any terminal when the power is switched on. DO NOT touch any internal circuit in 1 minute after the
power is switched off.
Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference.
Please use the fixed support accessory which is packed together with the product provided by Delta. DO NOT
tighten the screws out of the normal torque specifications; otherwise serious damage may occur.
Introduction
Explanation & Peripherals
Thank you for choosing Delta TP Series. TP05G (BS2/BT2) has the features of high resolution 160×80 dots.
When the font is Traditional Chinese character and the font size is 8, TP05G (BS2/BT2) is able to display 14×7
Chinese character; TP08G (BS2/BT2) has the features of high resolution 240×128 dots. When the font is
Traditional Chinese character and the font size is 8, TP08G (BS2/BT2) is able to display 21×11 Chinese
character. Both of them provide multilingual display and two built-in communication ports, one is for RS-232 and
the other is for RS-485/RS-422. RS-232 and RS-485 can be used simultaneously. Besides, they also support
built-in RTC, communication/alarm indication LED, etc. functions. Besides, the users can purchase program
copy card (optional) to copy settings and programs quickly and save download time. Regarding the editing
software, there are various objects and images for various users’ requirements. Please ensure to use TP series
with Delta power supply module, DVPPS01 and DVPPS02.
Product Outline
Power LED Indicator
Alarm LED Indicator
Display Area
Function Keys
Escape/Exit Key
Arrow Keys
Numeric Keys
Enter Key
Multiple Function Keys
Function Specifications
Model
Specifications
TP05G (BS2/BT2) TP08G (BS2/BT2)
Screen Type / Display
Color
STN-LCD / Monochromatic
Case Color BS2: White color, BT2: Black color
Backlight
The back-light automatic turn off time is 1~99 minutes (0 = do not turn off)
(The back-light life is about 50 thousand hours at 25°C)
Resolution 160×80 dots 240×128 dots
Display Range
83mm(W)× 41mm(H);
3.8” (diagonal preferred)
78mm(W)× 41mm(H);
3.8” (diagonal preferred)
Contrast Adjustment 10 levels of adjustment
Language/Font
ASCII: (Code page 850) Alphanumeric (including European characters)
Taiwan: (Big 5 codes) Traditional Chinese Fonts
China: (GB2324-80 codes) Simplified Chinese Fonts
5 × 8 dots 32 characters × 10 rows 48 characters × 16 rows
8 × 8 dots 20 characters × 10 rows 30 characters × 16 rows
8 × 12 dots
20 characters × 6 rows 30 characters × 10 rows
Display Text
8 × 16 dots
20 characters × 5 rows 30 characters × 8 rows
ENGLISH
Model
Specifications
TP05G (BS2/BT2) TP08G (BS2/BT2)
Font Size ASCII: 5×8, 8×8, 8×12, 8×16
Alarm LED Indicator (RED)
1. Power on indication (Blink for three times)
2. Communication error alarm
3. Special indication by user programming
Program Memory 1024KB flash memory
Serial Communication Port
RS-232(COM1)
Unsynchronized transmission method: RS-232
Data length: 7 or 8 bits, Stop bits: 1 or 2 bits
Parity: None/Odd/Even, Transmission speed: 9,600bps~115,200bps
RS-232: 9 PIN D-SUB male
Extension Communication
Port
RS-422(COM1)
RS-485(COM2)
Unsynchronized transmission method: RS-485 / RS-422
Data length: 7 or 8 bits, Stop bits: 1 or 2 bits
Parity: None/Odd/Even, Transmission speed: 9,600bps~115,200bps
RS-422: 9 PIN D-SUB male, RS-485: 6-Pin removal terminal
Battery Cover DC 3V battery for HMI
Extension Interface
1. Update firmware version
2. The slot for program copy card
6-Pin Removal Terminal Include DC 24V input and RS-485 communication input
Electrical Specifications
Model
Specifications
TP05G (BS2/BT2) TP08G (BS2/BT2)
Display Monochromatic STN LCD
Effective Display Area
83mm(W)× 41mm(H); 3.8” (diagonal
preferred)
78mm(W)× 41mm(H); 3.8” (diagonal
preferred)
Display Resolution 160×80
5×8 dots 32 characters × 10
rows
8×8 dots 20 characters × 10
rows
8×12 dots 20 characters × 6
rows
8×16 dots 10 characters × 5
rows
240×128
5×8 dots 48 characters × 16 rows
8×8 dots 30 characters × 16 rows
8×12 dots 30 characters × 10 rows
8×16 dots 30 characters × 10 rows
LCD Contrast Adjustment
Set by Software, adjust the contrast by the press button in the function table
LCD Backlight Type LED Backlight: Automatic Turn-off Setting
Function / Numeric Keys
0~9,F1~F5, ESC, ± , CLR, ←, ,SHIFT, ENTER and Arrow Keys (UP, DOWN )
External Input Power 24V (1.8W Max.)
Memory Capacity 1024K Byte
CPU ST STR710RZT6
RAM of System 64K Byte
Communication Interface
COM1: RS-232/RS-422 COM2: RS-485
Waterproof Class of Front
Panel
IP66 / NEMA4 / UL Type4 indoor
Operating Temperature
for Hardware
0~50°C; 20-90% RH (non-condensing)
Storage Temperature for
Hardware
-20~60°C
Vibration
5Hz f 9Hz = Continuous: 1.75mm / Occasional: 3.5mm
9Hz f 150Hz = Continuous: 0.5g / Occasional: 1.0g
Shock
15g peak, 11ms duration, half-sine, three shocks in each direction per axis,
on 3 mutually perpendicular axes (total of 18 shocks)
Radiated Emission CISPR11, Class A
Electrostatic Discharge
Immunity
EN61000-4-2
Radiated Immunity EN61000-4-3
Electrical Fast Transient
EN61000-4-4
Weight / Dimensions 0.43kg; 210×122×45mm (Width(W) × Height(H) × Deep(D))
Cooling Method Natural Air Cooling
Dimension and Installation
Product Outlook and Dimensions (Units: mm, [ ]: inch)
Back Panel
6-Pin Terminals:
Wire Gauge:12-24 AWG / Torque:4.5 lb.-inch
Front Panel and Right Side Diagram
210 [8.2677]
122 [4.8031]
45 [1.7717]
108.26 [4.262]
Mounting Dimensions (Panel Cutout)
Vertical View
196.26 [7.7266]
37.5 [1.4764]
7.5 [0.2953]
Installation
Please insert TP05G/TP08G to the opening hole of panel and tighten the screws. However, if a firm mounting
TP05G/TP08G to the panel is needed, please use the mounting fixed support accessory which is packed
together with TP05G/TP08G, then insert the fixed support in the back and tighten the screws. Please refer to
the following sections for correct installation. ( If the fixed support is not installed well, Delta will not
guarantee the waterproof function. The screw torque should be 4-5(kg-cm). DO NOT exceed this specification
when tightening the screws; otherwise TP05G/TP08G may be damaged.)
Do not install and mount TP05G/TP08G in the following environment.
A location subjected to Airborne dust, metallic particles, oil and smoke, corrosive or flammable
gases and liquids.
A location where temperature and humidity will exceed specifications.
A location where vibration and shock will exceed specifications.
The flat surface should be a UL Type 4 Indoor Use Only enclosure or equivalent (IP66/NEMA4). Please
refer to the figures below.
Installation Method of Insert Module
Password Function
If the users forgot the password, the password can be cleared by using the following code: 8888. This
universal code will clear the password and all TP05G/TP08G internal programs. The TP05G/TP08G will be
reset to the factory settings. Please pay close attention when using it. The password can be the alphabet from
A to Z or the number from 0 to 9. But it must use the function keys F0~F5 to input the password characters.
Please refer to the following table.
Function Key
Use Method Function Key
Use Method
Numeric Key
0 ~ 9 F3
Scrolls in a loop as follows
J→K→L→M→N→O→P→Q→R
F1
This key is left direction key and it can
be used to select the position of the
value.
F4
Scrolls in a loop as follows
S→T→U→V→W→X→Y→Z
F2
Scrolls in a loop as follows
A→B→C→D→E→F→G→H→I
F5
It can be a right direction key in the
system menu.
Hardware Operation
When the users want to startup TP05G/TP08G, a 24VDC power is needed. After applying 24VDC power to
TP05G/TP08G, it will enter into the startup display and then enter the user-designed program. Pressing Esc
key and holding on for 5 seconds can return to system menu. There are five selections in the system menu
and are described below.
SELECTIONS EXPLANAION
Download
Program
Use the connection cable (DVPACAB530) to connect the TP05G/TP08G serial communication
port RS-232 to a PC. Then use the TPEditor software to download an application program to
TP05G/TP08G.
Upload Program
Use the connection cable (DVPACAB530) to connect the TP05G/TP08G serial communication
port RS-232 to a PC. Then use the TPEditor software to upload an application program from
TP05G/TP08G.
Copy Program
Transfer a program between two TP05G/TP08G units.
1: Transmit Program ; 2: Receive Program
When transmit programs and data between two TP05G/TP08G units. Set one TP05G/TP08G to
“Receive Program” mode and the other TP05G/TP08G to “Transmit Program” mode. Please use
twisted pair wires to connect the two units via the RS-485 ports.
TP05G/TP08G
Settings
There are 8 items that used to modify TP05G/TP08G system settings:
1. Communication protocol: Setting the address of TP05G/TP08G, and the communication
string for either RS-232 or RS-485.
2. Contrast: Adjust the contrast of LCM display screen.
3. Back-light: adjust the automatic turn off time of LCM. Setting range is 00~99 seconds. If set
to 00, the LCM Back-light will not turn off.
4. Date and Time: It is used to set the TP05G/TP08G built-in RTC including year, month, day,
hour, minute, second and week. Also the internal battery capacity display is shown here.
5. Buzzer: Used to set the buzzer sound, normal mode or quiet mode.
6. Language Setting: Used to set the displayed language. English, Traditional Chinese,
Simplified Chinese or user-defined language.
7. Password setting: Used to set, enable, and disable the password function. If the password
function is enabled, it will require the user to input a password before entering any system
menu. The factory password is 1234.
8. Startup Display: Used to select the TP05G/TP08G startup display. User can select “user
defined” to use the file that designed by TPEditor software and download to TP05G/TP08G.
PLC Connection
There are three methods to connect to PLC:
1. Using TP05G/TP08G serial communication port (COM1) RS-232: set 8-pin DIP switch to
RS-485 mode and connect the cable (DVPACAB215 or DVPACAB230) to program
communication I/O RS-232C of PLC.
PLC Connection
2. Using extension communication port (COM2): set 8-pin DIP switch to RS-485 mode and
connect 5-pin removal terminal of extension communication port to RS-485 of PLC with
twisted pair.
3. Using extension communication port (COM1): set 8-pin DIP switch to RS-422 mode and
connect four pins (6, 7, 8, 9) of 9 PIN D-SUB male to RS-422 of PLC with 4-wire cable.
Execution
Execute the internal program that download from TPEditor software or transmitted from other
TP05G/TP08G units. When program is in execution, the user can return to system menu by
pressing Escape/Exit (Esc) key for 5 seconds.
Communication Connection
TP05/08G may connect to a PC by using connection able DVPACAB515
PC or TP05/08G
1
5
6
9
9 PIN D-SUB
TO PC (RS-232)
TO TP05/08G
5
1
9
6
9 PIN D-SUB
9 PIN D-SUB female
Rx 2
GND 5
5 GND
PC COM Port
9 PIN D-SUB female
3 Tx
2 Rx
TP05/08G COM Port
Tx 3
TP05/08G may connect to a DVP-PLC by using connection cable DVPACAB215/ DVPACAB230 /
DVPACAB2A30
1. DVPACAB215 DVPACAB230
TO PC or TP05/08G
1
13
14
1
5
6
9
25 PIN D-SUB
9 PIN D-SUB
TO PLC
MINI DIN TERMINAL
2. DVPACAB2A30
TO PC or TP05/08G
1
5
6
9
9 PIN D-SUB
TO PLC
MINI DIN TERMINAL
8 PIN MINI DIN
25 PIN D-SUB female
PC/TP COM Port PLC COM1 Port
Tx
2
GND 7
8 PIN MINI DIN
9 PIN D-SUB female
PC/TP COM Port PLC COM1 Port
4 Rx
8 GND
Rx 2
GND 5
1,2 5V
1
2
3
4
5
6
7
8
12
3
4
5
6
7
8
4 Rx
8 GND
1,2 5V
6
8
20
4
5
1
4
6
7
8
5 Tx
Rx 3
Tx 3
5 Tx
TP05G/08G The Pin definition of 9 PIN D-SUB
1. RS-232
3 Tx
5 GND
RS-232 9 PIN D-SUB male
TP05/08G COM Port
2 Rx
2. RS-422
8 Tx +
RS-422 9 PIN D-SUB male
9 Tx -
TP05/08G COM Port
7 Rx -
6 Rx +
3. DVPACAB630 (RS-422)
TO TP05/08G
1
5
6
9
9 PIN D-SUB
TO PLC
MINI DIN TERMINAL
8 PIN MINI DIN
9 PIN D-SUB female
TP05/08G COM Port
MITSUBISHI FX-PLC
Rx -
7
Tx+ 8
1
2
3
4
5
6
7
8
7 T
x+
2 Rx+
Tx - 9
3 SG
GND 5
Rx+
COM1 Port RS-422
6
4 Tx -
1 Rx -
Switch between RS-422 / RS-485 (by using 8-PIN DIP switch)
8-PIN DIP switch RS-485 RS-422
SW1 ~ SW4 On Off
SW5 ~ SW8 Off On
Battery Life and Precision of Calendar
Timer
Battery Life
Precision of Calendar Timer
1. At 0°C/32°F, less than -117 seconds error per month.
2. At 25°C/77°F, less than 52 seconds error per month.
3. At 55°C/131°F, less than -132 seconds error per month.
Temperature (°C) -20 0 20 60
Life (Year) 1.972 2.466 2.712 2.835
24V RS-485
TP05G (BS2/BT2) 160×80 8
14×7 TP08G (BS2/BT2) 240×128 8
21×11 RS-232 RS-485
RS-422 RS-232 RS-485 LED
DVPPS01 DVPPS02
TP05G (BS2/BT2) TP08G (BS2/BT2)
/ STN-LCD /
BS2 BT2
1 ~ 99 0
25 5
160 80 240 128
W H = 83 41 mm
3.8
W H = 78 41 mm
3.8
10
ASCII 850
BIG 5
GB2324-80
5 8 32 10 48 16
8 8 20 10 30 16
8 12 20 6 30 10
8 16 20 5 30 8
ASCII 5 8 8 8 8 12 8 16
1024KB
R S - 2 3 2 C O M 1
RS-232
7 8 1 2
None Odd Even 9,600bps ~ 115,200bps
RS-232 9 PIN D-SUB male
R S - 4 2 2 C O M 1
R S - 4 8 5 C O M 2
RS-485 RS-422
7 8 1 2
None Odd Even 9,600bps ~ 115,200bps
RS-422 9 PIN D-SUB male
RS-485 6Pin
3V
6 P i n 24V RS-485
TP05G (BS2/BT2) TP08G (BS2/BT2)
STN LCD
W H = 83 41 mm
3.8
W H = 78 41 mm
3.8
160 80
5 8
8 8
8 12
8 16
32 10
20 10
20 6
10 5
240
128
5 8
8
8
8 12
8 16
48 16
30 16
30 10
30 8
L C D
L C D LED
0 ~ F1 ~ F ES CL SHIF ENTER U DOWN
24V 1.8W Max.
1024K Byte
CPU ST STR710RZT6
R A M 64K Byte
COM1 RS-232 RS-422 COM2 RS-485
IP66 NEMA4 UL Type4 indoor
0 ~ 50 20 - 90 RH
-20 ~ 60
5Hz f 9Hz 1.75mm 3.5mm
9Hz f 150Hz 0.5g 1.0g
15g peak 11ms X, Y, Z 3 18
R F CISPR11 Class A
EN61000-4-2
R F EN61000-4-3
EN61000-4-4
0.43kg 210 122 45mm W H D