Filter
Top Products
Note: Full H.100 capabilities are not available with
this release of the Dialogic
®
D/82JCT-U.
1. Attach the end connector on the ribbon cable to
the CT Bus edge connector on the top edge of the
first board. The connectors are designed to fit
together one way only. If the connector does not
seat fully on the board, turn the cable around and
try again. Make sure that the colored stripe on the
cable faces toward the rear bracket. (The stripe
should be adjacent to pin 1 on the board
connector.) To preserve the electrical integrity of
the CT Bus, use a CT Bus cable with the
appropriate number of connectors (“drops”). It is
recommended that no more than two connectors
at either end of the cable be left unused.
2. Attach the ribbon cable to the next board until all
boards are connected by the cable.
Installing the CT Bus Cable
NOTE:
Your CT Bus cable may
have a different number
of connectors (drops).
CT Bus
Cable
Colored
Stripe
(Pin 1)
Note: To connect the CT Bus to an SCbus, attach
a CT Bus/SCbus Adapter (not included) to the CT
Bus board closest to the SCbus, and connect the
SCbus cable to this adapter. See the hardware
installation instructions for the CT Bus/SCbus
Adapter for more information.
3. If the ribbon cable has extra connectors or loose
cable, tuck the cable down so that it does not snag
when you replace the PC cover.
4. After installing and connecting all the boards,
replace the PC cover, cables, and cords.
Connecting External Cabling
A PBX station interface cable assembly that is specific
to the Dialogic
®
D/82JCT-U (available separately) is
used to connect the board to a punch-down block.
Connecting the Station Interface Cable
D/82U rear bracket
25-pair telco plug
36-position
mini-D cable plug
28 GA 18-pair
shielded cable
ID
To punch-down block
The station interface cable terminates at the punch-
down block end with a 25-pair, 57-series Amphenol
plug to allow available type-66 punch-down blocks to
be used to terminate the PBX station wiring. A 36-
position mini-D connector is used on the Dialogic
®
D/82JCT-U end of the cable.
To connect your Dialogic
®
D/82JCT-U board to a
punch-down block, follow the instructions below:
1. Connect the station interface cable’s 36-position
mini-D cable plug to the connector on the rear
bracket of the Dialogic
®
D/82JCT-U.
2. Connect the station interface cable’s 25-pair telco
plug to the connector on the punch-down block.
Hardware installation is now complete.
Connector Pin Numbering
1
12
36
26
25
50
25-pair connector
(attaches to the D/82U)
(attaches to the punch-down block)
36-position connector
The Telco plug cable connector tabulation is arranged
so that the four conductors of one station set circuit
are adjacent on a standard, type-66 punch-down
block. The pattern shown in the following figure
continues down the connector to encompass all eight
channels with two pairs of conductors per channel, for
a total of 16 twisted conductor pairs.
Telco Plug Connector Pinout
2
6
Ch. 1: 4-wire transmit Ch. 1: 4-wire transmit
Ch. 1: 2-wire transmit/receive
or Ch.1: 4-wire receive
Ch. 1: 2-wire transmit/receive
or Ch.1: 4-wire receive
Ch. 2: 2-wire transmit/receive
or Ch. 2: 4-wire receive
Ch. 2: 2-wire transmit/receive
or Ch. 2: 4-wire receive
Ch. 2: 4-wire transmit
Ch. 2: 4-wire transmit
1
After Installing the Hardware
After installing the hardware, run the Dialogic
®
Configuration Manager (DCM) as described in the
installation instructions included with the Dialogic
®
System Software to configure your system.
For technical specifications and product information
go to:
http://www.dialogic.com/products.htm.
Warranty and Return
Information
Warranty Period
For specific warranty information for this board, refer
to the Warranty section of the Products page, located
at this URL: http://www.dialogic.com/warranties/.
Contacting Technical Support
Dialogic provides technical support for its products
through a network of value added distributors who are
trained to answer technical questions on installing and
configuring Dialogic
®
products. If you are unsure how
to contact your support channel, please call Dialogic
in the United States at 973-967-6600 (9am-5pm EST)
and we will assist in obtaining the appropriate support
channel.
Outside the United States please refer to
http://www.dialogic.com/support/contact to obtain
local contact information. Dialogic also provides direct
support via Dialogic
®
Pro™ Services agreements. For
more details of direct support from Dialogic please
refer to:
http://www.dialogic.com/support/DialogicPro.
Returning a Product
To return a board for warranty repair or any other
returns, please refer to the following:
http://www.dialogic.com/support/hwfaults.
Sales Assistance
If you have a sales question, please contact your
local Sales Representative or the Regional Sales
Office for your area. Address, telephone and fax
numbers, are available at the Dialogic website located
at:
http://www.dialogic.com/contact.htm.
To purchase Dialogic
®
products, please refer to the
following website to locate the appropriate supplier:
http://www.dialogic.com/purchase.htm.
All contents of this document are furnished for informational use only
and are subject to change without notice and do not represent a
commitment on the part of Dialogic Corporation or its subsidiaries
(“Dialogic”). Reasonable effort is made to ensure the accuracy of the
information contained in the document. However, Dialogic does not
warrant the accuracy of this information and cannot accept
responsibility for errors, inaccuracies or omissions that may be
contained in this document.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN
CONNECTION WITH DIALOGIC
®
PRODUCTS. NO LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO
ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY
THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED
AGREEMENT BETWEEN YOU AND DIALOGIC, DIALOGIC
ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC
DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY,
RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS
INCLUDING LIABILITY OR WARRANTIES RELATING TO
FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY,
OR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY
RIGHT OF A THIRD PARTY.
Dialogic products are not intended for use in medical, life saving, life
sustaining, critical control or safety systems, or in nuclear facility
applications.
It is possible that the use or implementation of any one of the concepts,
applications, or ideas described in this document, in marketing
collateral produced by or on web pages maintained by Dialogic may
infringe one or more patents or other intellectual property rights owned
by third parties. Dialogic does not provide any intellectual property
licenses with the sale of Dialogic products other than a license to use
such product in accordance with intellectual property owned or validly
licensed by Dialogic and no such licenses are provided except pursuant
to a signed agreement with Dialogic. More detailed information about
such intellectual property is available from Dialogic’s legal department
at 9800 Cavendish Blvd., 5
th
Floor, Montreal, Quebec, Canada H4M
2V9. Dialogic encourages all users of its products to procure all
necessary intellectual property licenses required to implement any
concepts or applications and does not condone or encourage any
intellectual property infringement and disclaims any responsibility
related thereto. These intellectual property licenses may differ
from country to country and it is the responsibility of those who
develop the concepts or applications to be aware of and comply
with different national license requirements.
Dialogic, Diva, Eicon, Eicon Networks, Eiconcard and SIPcontrol,
among others, are either registered trademarks or trademarks of
Dialogic. Dialogic's trademarks may be used publicly only with
permission from Dialogic. Such permission may only be granted by
Dialogic’s legal department at 9800 Cavendish Blvd., 5th Floor,
Montreal, Quebec, Canada H4M 2V9. Any authorized use of Dialogic's
trademarks will be subject to full respect of the trademark guidelines
published by Dialogic from time to time and any use of Dialogic’s
trademarks requires proper acknowledgement. The names of actual
companies and products mentioned herein are the trademarks of their
respective owners.