Filter
Top Products
IMPORTANT:
Refer to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
IMPORTANT:
Refer to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
XTP T UWP 202 • Setup Guide
The XTP T UWP 202 is a two-input XTP Decora
®
Wallplate Transmitter that can be installed into a UL Listed metal junction box or the provided
mud ring. This guide provides instructions for an experienced installer to install and connect the XTP T UWP 202.
Throughput and Control
Connections
Power Connection,
Reset Button, and
Input Connections
A
XTP output connector
B
RS-232 and IR Over
XTP connector
C
Remote RS-232
connector
D
LAN connector (LAN
model only)
E
USB configuration
connector
F
DC power connector
G
Reset button
H
HDMI connector
I
Analog audio input
connector
J
Female 15-pin HD
connector
Figure 1. XTP T UWP 202 Rear (Left) and Front (Right) Panel Features (LAN Model)
Installation
Planning
CAUTION: Risk of personal injury. Failure to check the items
listed below may result in personal injury.
ATTENTION: Failure to check the items listed below may result in
property damage.
NOTE: If a junction box is required, it must be metal.
Ensure the installation meets the building, electrical, and safety codes.
Mounting and Cabling
For additional mounting considerations, see the XTP T UWP 202
User Guide at www.extron.com. For metal junction boxes, refer to the
manufacturer for additional mounting instructions and considerations.
Step 1 — Prepare the installation site
a. Using a soft pencil, mark cut guidelines on the mounting surface. For
accuracy, use a template or the mounting enclosure.
NOTE: Install junction boxes against a wall stud (see figure 2).
b. Cut a hole in the wall. To avoid making the hole too big, cut inside the
marked lines.
c. If using the mud ring in a wall with insulation inside, remove at least
6 inches of the insulation in all directions around the cutout. If a wall
stud interferes with removing the insulation, remove as much as
possible between the cutout and the wall stud.
d. Test the t by inserting the mud ring or metal junction box into the
hole in the wall. If necessary, enlarge the hole as needed.
Step 2 — Install the metal junction box or mud ring
To install a UL Listed metal junction box, use mounting screws to fasten
the box to a wall stud (see gure 2).
To install the provided mud ring to the wall, attach the mounting screws to
the mud ring and loosely attach backing clips to the ends of the screws.
Rotate the backing clips so the mud ring ts in the opening and then rotate
them to t snugly against the back of the wall (see gure 3).
Figure 2. Metal Junction Box Installation
Tx
RS-232
XTP T UWP 202
RS-232IR
Rx Tx RxGTxRxG
12V
1.0 A MAX.
POWER
OVER XTP
XTP OUT
REMOTE
PWR HDCP HDMI
HDMI IN
LAN
VGA
RESET
CONFIG
AUDIO
CLIP
AUTO
SWITCH
AUDIO IN
VGA IN
BCF
A
H
DE
IG
Rear
Front
J
Figure 3. Mud Ring Installation
XTP T UWP 202
Signal Output
Cable
Cable
Clam
p
Decora Faceplate
Screws or
Nails
Wall opening is
flush with edge
of box.
Wall Stud
PWR
HDCP
HDMI
HDMI IN
LAN
VGA
RESET
CONFIG
AUDIO
CLIP
AUTO
SWITCH
AUDIO IN
VGA IN
Backing Clip
Mounting Screw
Rotate the Backing Clip
out of the way to insert
the mud ring into the wall.
XTP T UWP 202
Decora Faceplate
PWRHDCPHDMI
HDMI IN
LAN
VGA
RESET
CONFIG
AUDIO
CLIP
AUTO
SWITCH
AUDIO IN
VGA IN