Filter
Top Products
2929
2 AC IN terminal (DT-V9L5 only)
AC power input connector.
Connect the provided AC power cord to an AC outlet.
● Attach the provided power cord holder to prevent accidental disconnection of the AC power cord. (☞ “Attaching the power cord holder”
on page 46)
CAUTION
Do not connect the power cord until all other connections are completed.
3 For DT-V9L5: DC switch / For DT-F9L5: POWER switch
Turns the DC power on or off.
● You need to press button (☞ q on page 27) on the front panel to turn on the monitor after turning on the DC switch.
● The monitor consumes the battery even while the monitor is on standby. To save battery life, turn off this switch.
4 DC IN terminal
DC 12 V (maximum DC 17 V) power input connector.
● While using both the AC and DC power supply, AC power supply is preferentially used. If the AC power supply is cut off (for example, when
turning off the POWER switch), the power supply automatically switches to the DC power supply.(DT-V9L5 only)
● Use a DC power supply with the LPS (Limited Power Sources) function.
5 VIDEO/COMPONENT terminals (BNC)
IN: Input terminals for the composite (VBS) and the analog component (Y/PB/PR) signals.
Select the signal type in “Video/Component Select” corresponding to the type of the input signal. (☞ page 34)
OUT: Output terminal for the composite (VBS) and the analog component (Y) signals.
6 AUDIO (IN) terminal (pin jack)
Input terminal for the analog audio signals.
● Use this terminal for the analog audio connection of the SDI. To select the audio output, set in “Audio Setting” of the Main Menu.
● When you use HDMI input for the picture and analog sound for the audio signal, input analog sound into this terminal, and set in “Audio
Setting” of the Main Menu. (☞ page 35)
7 HDMI terminal
Input terminal compatible with HDCP for the HDMI signal. (TYPE-A)
8 REMOTE terminal
Terminal for controlling the monitor by an external control. (☞ “External Control” on page 42)
9
AUDIO (MONITOR OUT) terminals (pin jack)
Output terminals for the analog audio signal.
● The terminals emit the audio signals through the AUDIO (IN) terminal or EMBEDDED AUDIO signals through the E. AUDIO HD/SD SDI (IN 1
or IN 2) input terminal.
●
The signal is output from this terminal only when the monitor is on or in “Power Save” (power save) mode (☞ “No Sync Action” on page 36).
● The EMBEDDED AUDIO signal...
is decoded into an analog signal, then emitted. –
is emitted only when “SDI 1” or “SDI 2” is selected, and when EMBEDDED AUDIO signals come in to the E. AUDIO HD/SD SDI (IN 1 or IN 2) –
terminal.
● Audio signals are only output from the HDMI terminal when the signals are not protected by HDCP.
Even when the signals are protected by HDCP, sound is emitted from the speakers (DT-V9L5 only) and the headphones. –
p E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)
Input terminals for the HD/SD SDI signals.
● The terminals accept also EMBEDDED AUDIO signals including up to 16 audio channels with a sampling frequency of 48 kHz.
q E. AUDIO HD/SD SDI (SWITCHED OUT) terminal (BNC)
Output terminal for the HD/SD SDI signals.
● The SDI signals of the current input (SDI 1 or SDI 2) are re-clocked, then emitted.
● When an input other than SDI 1 and SDI 2 is selected, the SDI signal of the input selected last time is emitted from this terminal.
● The signals are emitted from this terminal only when the monitor is on or in “Power Save” (power save) mode
(☞ “No Sync Action” on
page 36)
.
w Screw holes for external battery attachment (DT-V9L5 only)
Attach external battery for DC power supply by using 2 screw holes. Choose the appropriate screw holes from 1, 2 or 3 according to the type
of external battery. (Depending on the battery type.)
Use the Anton Bauer Dionic 90 (mount: QR DXC-M3A) external battery.
CAUTION
● Do not use the external battery for DC 24 V power supply.
● Use only the battery specified above. If a heavy battery is used, it may fall off depending on the way the monitor is used.
Note for connections
Before making any connections, turn off all the equipment.•
Use a cord whose plugs correctly match the terminals on this monitor and the equipment.•
Plugs should be firmly inserted; poor connections could cause noise.•
When unplugging a cord, be sure to grasp its plug and pull it out.•
DO NOT connect the power cord until all connections are complete.•
Refer also to the user manual of each piece of equipment.•
When using DC 12 V power (maximum DC 17 V), check the DC IN terminal pin signal, and use the correct
polarity. If the polarity is reversed, this could cause a fire or personal injury.