Filter
Top Products
User Warranty Registration
Please register on-line @ http://www.omnitron-systems.com or complete both sides
and mail or fax this registration form to:
Omnitron Systems Technology, Inc.
27 Mauchly #201
Irvine, CA 92618, USA
Fax: (949) 250-6514
Name: _________________________________________________
Company: ______________________________________________
Address: ______________________________________________
______________________________________________
City: ___________________ State: _______ Zip Code: ________
Country: _______________________________________________
Phone: ____________________ Fax: _______________________
E-mail: _________________________________________________
Please complete both sides of this form
FlexSwitch
TM
600XC 4U and 1Fx+4U
User Instructions
Description:
The FlexSwitch
TM
600XC described here is a four-port
10/100 auto-sensing switch with an optional switched
Fast Ethernet fiber uplink. It operates in half duplex (HD)
or full duplex (FD). The following multimode and single-
mode models are described here:
Ext. Power Int. Power
Model Model UTP RJ45 Fiber
6701 6501 4 @ 10/100 None
6750-F1
1
6550-F1
1
4 @ 10/100 1 @ 100 SC
6751-F1
1
6551-F1
1
4 @ 10/100 1 @ 100 ST
1.
The “
F1
” denotes the fiber type used on the fiber port.
Power Adapter Notice:
1. When used with an external power adapter (models
67xx), this product must only be used with Omnitron
Supplied Power Unit model number 9112-PS.
2. When used with an external power adapter (models
67xx), this product is intended to be and must be used
only with a Listed Direct Plug-In Power Unit marked
“Class 2” and rated at 9Vdc, 1.2 Amp.
3. Models using internal power supplies (models “65xx”)
are capable of auto switching from 100-230V, and
are supplied with a U.S. type NEMA 5-15 power cable.
4. For products being shipped outside of the U.S., the
user is required to install a properly grounded IEC 320-
appliance cable with a minimum rating of 10 AMPs.
5. User-supplied cables must meet the required safety
agency approvals, applicable international standards
and electrical ratings for the region.
WARNING!
Before inserting the Power Adapter, verify that
the power on the unit is appropriate
for your AC line voltage source.
Mounting and Cable Attachment:
The FlexSwitch 600XC can be used as a tabletop unit or
wall-mounted using a wall-mounting kit.
After connecting to an appropriate power outlet, attach the
FlexSwitch 600XC UTP ports via category 5 cables to properly
configured and operational 10Base-T or 100Base-Tx Ethernet
workstations, hubs or switches. Verify that the LEDs display
the expected (10 or 100, half or full duplex) status. Note that
UTP port one has a built-in crossover switch that facilitates
the usage of a straight-through cable for a hub, switch or
workstation connection.
(For models with fiber)
Attach the FlexSwitch 600XC module via an appropriate fiber
cable (SC or ST as needed) to a 100Base-Fx Fast Ethernet
fiber switch, hub or workstation. The fiber’s transmit (Tx) must
attach to the receive side on the opposing device and the
receive (Rx) must attach to the transmit side. Set the “Half/
Full Duplex” switch as needed.
Switch Settings:
UTP “Crossover” Switch: When connecting port one
to a hub or switch, set the switch to “Crossover.” When
connecting to a workstation, set it to “Straight-Through”
(factory setting).
“Full-Duplex (FDX) / Half-Duplex (HDX)” Switch:
(
For models with fiber
)
When the FDX / HDX switch is set to “Half-Duplex”, the
fiber port operates in half duplex. When set to “Full-
Duplex” (factory setting), the fiber port operates in full
duplex. Half duplex
must be used when connecting to a
hub. Full duplex
should be used when connecting to a
switch or a full-duplex workstation.
Manual Port Configuration with Switches
The FlexSwitch 600XC has the ability to configure ports
to a particular speed (10 or 100Mbps) or duplex (half/full-
duplex) through the use of switches. These Switches are
located on the side of the unit and control the four UTP
ports. Setting the the switches to “Auto” enables the port
to determine the speed and duplex mode automatically.
If the connected device cannot provide the proper signal
to indicate its own mode of operation, the manual switches
should be used. This feature allows connections with
devices that do not auto-negotiate properly. Use the
following steps to manually configure these ports.
1. Turn off auto-negotiiation (Auto) to the desired port by
setting the approprate switch to the manual position
(Man).
2. Adjust the 10/100 Mbps switch to the speed of the
connecting device and check for link status.
3. Adjust the half/full-duplex switch to accommodate the
connecting device and check for link status.
Please use the following to identify your model:
F1 = 0, 2, 3
0 = Multimode Lx 1300nm
2 = Single-mode Lx 1300nm
3 = Single-mode Lx/LH 1300nm Extended Distance
User Warranty Registration
Please register online at http://www.omnitron-systems.com or complete both sides
and return this form to Omnitron Systems.
FlexSwitch Type: ________ Fiber Type:_______Connector: _______
Model:_________________________________________________
Serial Number: ______________ Purchase Date: ______________
Purchased From: _________________________________________
Address: ______________________________________________
City: ___________________ State: _______ Zip Code: ________
Country: _______________________________________________
Comments and Suggestions: _______________________________
______________________________________________________
______________________________________________________
Please complete both sides of this form
Warning
The operating description in this Instruction Manual is
for use by qualified personnel only. To avoid electrical
shock, do not perform any servicing of this unit other
than that contained in the operating instructions, unless
you are qualified and certified to do so by Omnitron
Systems Technology, Inc.
Caution
All user-required operations can be performed without
opening the unit. Never attempt to open or remove the
cover or tamper with the unit.
Warranty
This product is warranted to the original purchaser
against defects in material and workmanship for a period
of TWO YEARS from the date of shipment. A LIFETIME
warranty may be obtained by the original purchaser by
REGISTERING this product with Omnitron within 90 days
from the date of shipment. TO REGISTER, COMPLETE
AND MAIL OR FAX THE REGISTRATION PORTION
OF THIS INSTRUCTION MANUAL TO THE INDICATED
ADDRESS. Or you may register your product on the
internet at http://www.omnitron-systems.com. During the
warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective.
For warranty service, the product must be sent to an
Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the
product to Buyer’s designated US address using
Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting
from improper or inadequate use and/or maintenance
of the equipment by Buyer, Buyer-supplied equipment,
Buyer-supplied interfacing, unauthorized modifications
or tampering with equipment (including removal of
equipment cover by personnel not specifically authorized
and certified by Omnitron), or misuse, or operating
outside the environmental specification of the product
(including but not limited to voltage, ambient temperature,
radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron
specifically disclaims the implied warranties of
merchantability and fitness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and
exclusive remedies. Omnitron shall not be liable for any
direct, indirect, special, incidental, or consequential damages,
whether based on contract, tort, or any legal theory.
Doc #: 040-06750-001 4/00
LED Indicators:
Function Color Description
Power:
Power Yellow Off: No power detected
On: Power detected
Copper:
10/100 Green/Yellow Yellow On: 10
Green On: 100
Yellow or Green Flashing:
Activity detected
FDX/HDX Green Off: Set to Half-Duplex
On: Set to Full-Duplex
Fiber: (
For models with fiber
)
Link/Act Green Off: No Link detected
On: Link detected
Flashing: Data Received
Technical Support
For help with this product, contact our Tech Support:
Phone: (949) 250-6510
Fax: (949) 250-6514
Address: Omnitron Systems Technology, Inc.
27 Mauchly #201
Irvine, CA 92618 USA
Email: support@omnitron-systems.com
URL: http://www.omnitron-systems.com