Oregon CP100 Clock User Manual


  Open as PDF
of 2
 
CLOCK
To set the clock:
1. Press and hold
CLOCK for 2 seconds. The setting
will blink.
2. Use
/ to change the setting.
3. Press
CLOCK to confirm.
4. The settings order is: 12 / 24 hour format, hour,
minute, year, month-day format, month and day.
LCD DISPLAY
Use motion above the IR motion sensors to toggle display
mode between:
• Clock
• Calendar
• Alarm
• Indoor temperature
NOTE The IR motion sensors range is from 2.5 to 15 cm
(1 to 6 in) above the sensor. Any movement outside this
range will not be detected.
ALARM
To set the alarm:
1. Press
ALARM or navigate to Alarm display.
2. Press and hold
ALARM for 2 seconds to enter alarm
setting mode. The setting will blink.
3. Use
/ to change the setting for hour.
4. Press
ALARM to confirm.
5. Repeat steps 3 and 4 to set minute.
appears when
the alarm is set.
To silence the alarm:
• Use motion above the IR motion sensors to activate
the 8-minute SNOOZE feature.
OR
• Press ALARM, CLOCK
, or to mute the alarm
and automatically activate the alarm again after 24
hours.
To activate / deactivate the alarm:
• Press ALARM ON / OFF.
PROJECTION
The ultra-bright LED enables daylight projection of time
and temperature information.
To activate projection:
Slide PROJECTION to AUTO or CLOCK.
• Slide to AUTO to toggle between current time and
indoor temperature.
• Slide to CLOCK to project current time only.
To adjust the projection image:
• Switch
CDS to ON to activate automatic projection
dimming.
• Press
180° ROTATION to rotate the image by 180°.
• Focus the projector image by turning the FOCUS
wheel.
NOTE Please take care not to look into the projector.
Oregon Scientific will not be held responsible for any
results or consequences arising from the misuse of this
product.
TEMPERATURE
Press °C / °F to select the temperature display unit.
RESET
To return the unit to the default settings, insert a thin blunt
object into the RESET hole.
PRECAUTIONS
This product is engineered to give you years of
satisfactory service if you handle it carefully. Here are a
few precautions:
• Do not cover the ventilation holes. Make sure items
that are nearby such as newspapers, tablecloths,
curtains etc cannot accidentally cover the ventilation
holes.
• Placement of this product on wood surfaces with
certain types of finishes, such as clear varnish, may
result in damage to the finish. Consult the furniture
manufacturer’s care instructions for direction as to
the types of objects that may safely be placed on
the wood surface. Oregon Scientific shall not be
responsible for any damage to wood surfaces from
contact with this product.
• Do not immerse the unit in water. If you spill liquid
over it, dry it immediately with a soft, lint-free cloth.
• Do not clean the unit with abrasive or corrosive
materials. This may scratch the plastic parts and
corrode the electronic circuit.
• Do not subject the unit to excessive force, shock,
dust, temperature or humidity, which may result in
malfunction, shorter electronic life span, damaged
battery and distorted parts.
Daylight Projection Clock
Model: DP100
USER MANUAL
INTRODUCTION
Thank you for selecting the Oregon Scientific
TM
daylight
projection clock (DP100).
NOTE Please keep this manual handy as you use
your new product. It contains practical step-by-step
instructions, as well as technical specifications and
warnings you should know about.
OVERVIEW
FRONT VIEW
2
3
4
1
6
5
1. CDS light sensor: Adjusts projection brightness
2. ALARM ON / OFF: Activate / deactivate alarm
3. LCD display: Clock, alarm, calendar and indoor
temperature
4. : Alarm icon
5. IR motion sensors: Snooze; change display mode
6. Projector: Projects time, alarm status and indoor
temperature
BACK AND BASE VIEW
1
2
3
6
7
8
9
10
4
5
1. FOCUS: Focus the projected image
2. Temperature sensor and adapter slot
3. CLOCK: Enter clock setting mode
4. / : Increase / decrease setting
5. PROJECTION OFF / CLOCK / AUTO: Select
projection mode
6. ALARM: Enter alarm setting mode
7. 180° ROTATION: Rotate projection image by 180°
8. °C / °F: Select temp erature unit
9. RESET: Return to default settings
10. CDS ON / OFF: Activate light sensor
GETTING STARTED
ADAPTER
Insert the adapter into the adapter slot as shown.
EN
• Do not tamper with the unit’s internal components.
Doing so will invalidate the warranty on the unit and
may cause unnecessary damage. The unit contains
no user-serviceable parts.
• Do not dispose this product as unsorted municipal
waste. Collection of such waste separately for special
treatment is necessary
• Due to printing limitations, the displays shown in this
manual may differ from the actual display.
• The contents of this manual may not be reproduced
without the permission of the manufacturer.
NOTE The technical specifications for this product and
the contents of the user manual are subject to change
without notice.
SPECIFICATIONS
TYPE DESCRIPTION
Unit dimension 138 x 88 x 44 mm
(H x W x D) (5.4 x 3.5 x 1.7 in)
Unit weight 523g (18.4 oz)
Clock format 12 / 24-hour
Alarm duration 2 min
Snooze 8 min
Temperature range 0°C to 50°C
(32°F to 122°F)
Temperature resolution 1°C (1°F)
Projector rotation angle + / - 90°
IR sensor coverage distance 2.5 to 15 cm
(1 to 6 in)
Power DC 5.0V adapter
ABOUT OREGON SCIENTIFIC
Visit our website (www.oregonscientific.com) to learn
more about Oregon Scientific products such as digital
cameras; MP3 players; children’s electronic learning
products and games; projection clocks; health and
fitness gear; weather stations; and digital and conference
phones. The website also includes contact information
for our Customer Care department in case you need
to reach us, as well as frequently asked questions and
customer downloads.
We hope you will find all the information you need on our
website, however if you’re in the US and would like to
contact the Oregon Scientific Customer Care department
directly, please visit:
www2.oregonscientific.com/service/default.asp
OR
Call 1-800-853-8883.
For international inquiries, please visit:
www2.oregonscientific.com/about/international.asp
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
WARNING Changes or modifications not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV
technician for help.
DECLARATION OF CONFORMITY
The following information is not to be used as contact
for support or sales. Please call our customer service
number (listed on our website at
www.oregonscientific.com), or on the warranty card for
this product) for all inquiries instead.
We
Name: Oregon Scientific, Inc.
Address: 19861 SW 95th Ave.,
Tualatin, Oregon 97062 USA
Telephone No.: 1-800-853-8883
declare that the product
Product No.: DP100
Product Name: Daylight Projection Clock
Manufacturer: IDT Technology Limited
Address: Block C, 9/F, Kaiser Estate,
Phase 1,41 Man Yue St., Hung
Hom, Kowloon, Hong Kong
is in conformity with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: 1) This device
may not cause harmful interference. 2) This device must
accept any interference received, including interference
that may cause undesired operation.
INTRODUCTION
Merci d’avoir sélectionné l’Horloge à Projection de Jour
de Oregon Scientific
TM
. (Modèle DP100).
REMARQUE Veuillez conserver ce manuel pour toutes
références ultérieures. Il contient toutes les instructions
pratiques, les caractéristiques techniques et les
avertissements à prendre en compte.
VUE D’ENSEMBLE
FACE AVANT
2
3
4
1
6
5
1. Capteur de lumière CDS: Ajuste la clarté de
projection
2. ALARM ON / OFF: Permet d’activer / désactiver
l’alarme
3. Affichage LCD: Horloge, alarme, calendrier et
température intérieure.
4. : Icône de l’alarme
5. Capteurs de mouvement infra rouge: Snooze
(Rappel d’alarme) ; changement du mode
d’affichage
6. Projecteur: Permet de projeter l’heure, l’état de
l’alarme et la température intérieure
VUE DE DOS ET VUE INFERIEURE
1
2
3
6
7
8
9
10
4
5
1. FOCUS: Permet de mettre au point l’image du
projecteur
2. Capteur de température et prise adaptateur
3. CLOCK: Permet d’entrer dans le mode réglage de
l’horloge
4. / : Permet d’augmenter / diminuer les valeurs de
réglage.
5. PROJECTION OFF / CLOCK / AUTO: Permet de
sélectionner le mode de projection
6. ALARM: Permet d’entrer dans le mode réglage de
l’alarme
7. 180° ROTATION: Permet de faire tourner l’image à
180°
8. °C / °F: Permet de sélectionner l’unité de mesure de
la température
FR
9. RESET: Permet de revenir aux réglages par défaut
10. CDS ON / OFF: Permet d’activer le capteur de
lumière
AU COMMENCEMENT
ADAPTATEUR
Branchez l’adaptateur dans la prise adaptateur comme
indiqué.
HORLOGE
Pour régler l’horloge :
1. Appuyez et maintenez enfoncée la touche
CLOCK
pendant 2 secondes. Le réglage clignotera.
2. Utilisez
/ pour changer le réglage
3. Appuyez sur
CLOCK pour confirmer.
4. L’ordre de réglage est le suivant : Format 12/24
heures, heure, minutes, année, format mois/jour,
mois et jour.
AFFICHAGE LCD
Utilisez le signe situé au dessus des capteurs de
mouvement infra rouge pour alterner entre les modes
suivants :
• Horloge
• Calendrier
• Alarme
• Température intérieure
REMARQUE La portée des capteurs de mouvement
infra rouge est de 2,5 à 15 cm (1 à 6 pouces) au dessus
du capteur. Tout mouvement hors de cette portée ne
sera pas détecté.
ALARME
Pour régler l’alarme :
1. Appuyez sur ALARM ou entrez dans l’affichage de
l’Alarme
2. Appuyez et maintenez enfoncée la touche ALARM
pendant 2 secondes pour entrer dans le mode de
réglage de l’alarme. Le réglage clignotera.
3. Utilisez
/ pour changer le réglage de l’heure
4. Appuyez sur
ALARM pour confirmer.
5. Répétez les étapes 3 et 4 pour régler les minutes
s’affichera une fois l’alarme réglée.
Pour couper le son de l’alarme :
• Utilisez le signe situé au dessus des capteurs de
mouvement infra rouge pour activer la fonction
SNOOZE (rappel d’alarme) de 8 minutes.
OU
• Appuyez sur ALARM, CLOCK,
ou pour couper
le son de l’alarme et la réactiver automatiquement 24
h plus tard.
Pour activer / désactiver l’alarme :
• Appuyez sur ALARM ON / OFF.
PROJECTION
La forte clarté de la diode électroluminescente permet une
projection en journée de l’heure et de la température.
Pour activer la projection :
Placez l’encoche
PROJECTION sur AUTO ou sur
CLOCK.
• Placez l’encoche sur
AUTO pour alterner entre
l’heure actuelle et la température intérieure.
• Placez l’encoche sur
CLOCK pour ne projeter que
l’heure actuelle.
Pour ajuster l’image projetée :
• Placez
CDS sur ON pour activer la gradation de
projection automatique.
• Appuyez sur 180° ROTATION pour faire tourner
l’image à 180°.
• Tournez la molette FOCUS pour mettre au point
l‘image projetée.
REMARQUE Faîtes attention à ne pas regarder dans
le projecteur. Oregon Scientific ne sera en aucun cas
responsable des conséquences ou résultats découlant
de la mauvaise utilisation de ce produit.
TEMPERATURE
Appuyez sur °C / °F pour sélectionner l’unité d’affichage
de la température.
DP100 MANUAL (E-F-ES).indd 1 5/19/06 4:18:37 PM
P/N: 086L004396-020 REV1
1/2