Filter
Top Products
9. Multi-unit Operation
55
9 Multi-unit OperationAdditional Units
9.1 Operating additional units
9.1.1 Additional cordless handsets
Up to 6 cordless handsets can be registered to the base
unit. Additional cordless handsets will give you the
freedom to, for example, have an intercom call with
another cordless handset while a third cordless handset
is on an outside call.
Important:
L The additional cordless handset model
recommended for use with this unit is noted on
page 7. If other model cordless handset is used,
certain operations (cordless handset settings,
base unit settings, etc.) may not be available.
9.2 Registering a cordless
handset to a base unit
The included cordless handset and base unit are
preregistered. If for some reason the cordless handset is
not registered to the base unit (for example, w flashes
even when the cordless handset is near the base unit),
register the cordless handset manually.
After purchasing an additional cordless handset, register
it to the base unit. Ensure that the additional cordless
handset is switched ON. If it is not ON, press and hold
{ih} for few seconds to turn the cordless handset ON.
1 {j/OK} i “Handset Setup” i {>}
2 “Registration” i {>}
3 “Register H.set” i {>}
4 Press and hold {LOCATOR} on the base unit for
about 3 seconds, until the registration tone sounds.
L After pressing {LOCATOR}, the rest of this
procedure must be completed within 1 minute.
5 Wait until “Enter Base PIN” is displayed, then
enter the base unit PIN (default: “0000”), then press
{j/OK}.
L If you forget your PIN, consult your nearest
Panasonic service centre.
L When the cordless handset has been registered
successfully, w will stop flashing. If keytones are
turned ON (page 52), a confirmation tone will be
heard.
Note:
L Charge the batteries of your additional cordless
handset for about 7 hours before initial use.
9.2.1 Cancelling a cordless handset
A maximum of 6 cordless handsets can be registered to
a base unit. A cordless handset can cancel its own
registration (or the registration of another cordless
handset) that is stored in the base unit. This will allow the
base unit to forget the cordless handset.
1 {j/OK} i “Base Unit Setup” i {>}
2 Enter “335”.
3 “Cancel Handset” i {>}
L The numbers of all cordless handsets registered
to the base unit are displayed.
4 Select the cordless handset(s) you want to cancel,
by pressing the desired cordless handset number.
L The selected cordless handset number(s) will
flash.
L To cancel a selected cordless handset number,
press the number again. The number will stop
flashing.
5 {j/OK}
6 “Yes” i {>} i {ih}
9.2.2 Increasing the range of the base unit
You can increase the signal range of the base unit by
using a DECT repeater. Please use only Panasonic
DECT repeater. See page 7 for accessory information.
Important:
L Before registering the repeater to this base unit,
you must turn the repeater mode ON.
L Do not use more than one repeater at a time.
Setting the repeater mode
1. {j/OK} i “Base Unit Setup” i {>}
2. “Other Options” i {>}
3. “Repeater Mode” i {>}
4. “On” or “Off” i {>} i {ih}
Note:
L After turning repeater mode ON or OFF, w may flash
on the cordless handset momentarily. This is normal.
The cordless handset can be used once w stops
flashing.
Other Features
9.3 Intercom
Intercom calls can be made between a cordless handset
and the base unit, and between 2 cordless handsets.
You can page all cordless handsets at once from the
base unit.
9.3.1 Making intercom calls
With the cordless handset
1 {INT}
2 To page the base unit, press {0}.
To page another cordless handset, press the
desired cordless handset number.
L The base unit or the destination cordless
handset will beep (be paged) for 1 minute.
L To stop paging, press {ih}.
3 When the paged party answers, talk into the
cordless handset.
4 To end the intercom call, press {ih}.
FC228HK-PFQX2656ZA-en.book Page 55 Thursday, August 31, 2006 11:35 AM