Filter
Top Products
[7] Automatic Editing Control Section
q SPLIT button
For split editing, press this so that the button LED lights,
and then set the edit IN point to be split. Refer to set-up
menu item No.311 (SPLIT EDIT).
w LAST EDIT (CLEAR) button
LAST EDIT: This button accesses the previously pre-
viewed contents. (It alternately accesses two sets of con-
tents whose preview has been completed.)
CLEAR (SHIFT+LAST EDIT): These buttons delete the
registered event. The “d” display appears for EDL.
e – (BS) Minus trim button
–: When the IN or OUT point which has been input is to
be returned by one frame, this trim button is pressed
while the IN or OUT button is pressed. To use this
function continuously, keep pressing the buttons. To
set further back both the IN and OUT points simultane-
ously for editing, press this trim button while the IN and
OUT buttons are pressed.
BS (SHIFT+“–”): These buttons access the previous edit.
Keep pressing the button to execute the function continu-
ously.
r + (FS) Plus trim button
+: When the IN or OUT point which has been input is to
be advanced by one frame, this trim button is pressed
while the IN or OUT button is pressed. To use this
function continuously, keep pressing the buttons. To
advance both the IN and OUT points simultaneously
for editing, press this trim button while the IN and OUT
buttons are pressed.
FS (SHIFT+“+”): These buttons access the last event.
Keep pressing the button to execute the function continu-
ously.
t COUNTER switchs
These switches select the counter reference for VTR1
and VTR2.
CTL: At this switch position, the CTL pulse count after
resetting appears on the counter display. It is reset
by the RESET button.
TC: The time code (absolute value) which has been
read appears at this position. It is not reset even if
the RESET button is pressed.
UB: The user bit which has been read appears at this
position.
y GO TO/RECALL button
GO TO: To check the IN or OUT point image, press the
IN or OUT button while holding down the GO TO button.
In the audio split edit mode, the audio IN point is
searched when the IN button is pressed.
RECALL (SHIFT+GO TO): These buttons re-register an
event which was deleted in the EDL mode. The “d” dis-
play changes to “no display.”
CONTROLS AND THEIR FUNCTIONS
11
Controls and their functions
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
EJECT
VTR1
POWER
REC
CH1
RESET
REC
DIAG
REMOTE
EXT VTR
LOCAL-
VTR1 VTR2
CONTROL
ON
OFF
REC
INHIBIT
OFF
ON
CH2
PB
AUDIO LEVEL
REW
FF
STOP
STB OFF
TRACK
PLAY STILL
1ST EDIT
BS
EVENT
SPLIT
ASMBL
IN OUT
VTR1 VTR2 VTR1 VTR2
PREROLL
SYNCHRO
7
5
3
CF
ON
OFF
CH1
MIX
CH2
V1
V1•2
V2
SWAP
NORM
MIX
AUDIO
MONITOR
SPEAKER/
HEADPHONES
AUDIO
SWAP
DUMP LOAD
EDL
CLEAR
FS
RECALL
LAST
EDIT
VA1A2TC
PLAY
IN OUT
GO TO
ENTRY / SHIFT
EDIT MODE
COUNTER
CTL
TC
UB
VTR1
EJECT
VTR2
RESET
REC
STORE
STOP
STB OFF
MENU
EDIT
STILL
REW
FF
VTR2
REC
CH1 CH2
OPERATION MODE
VTR2 AUDIO
INPUT SELECT
EDIT
INT
EXT
SEPARATE
CH1 CH2
VTR1
EXT
PB
AUDIO LEVEL
PREVIEW
REVIEW MULTI
AUTO EDIT
ALL STOP
1 3 4 2 5 6
This button does not work when the SEPARATE MODE
switch has been set to SEPARATE.