Filter
Top Products
QUICK SETUP GUIDE • GUIDE D’INSTALLATION RAPIDE •
GUÍA DE INSTALACIÓN RÁPIDA
PATA 2.5 Hard Drive Enclosure
Boîtier pour disque dur
PATA de 2,5 po (6,35 cm)
Caja para disco duro PATA de 2.5"
RF-PHD25
Package contents
• RF-PHD25 enclosure • Carrying case
• High-speed USB 2.0 Y-cable • Screws (4)
• CD that contains Roxio BackOnTrack • Screwdriver
backup software and User Guide • Quick Setup Guide
System requirements
One USB port
Windows® 7, Windows Vista®, Windows® XP, or Mac OS 10.2.0 or higher.
Installing your hard drive in the enclosure
1 Remove the two screws from the back panel, then pull the tray out from
the enclosure.
2 Place a formatted hard drive into the tray, connect the data connector
to the corresponding connector on the enclosure board, then turn the
tray over and secure the drive to the metal plate with the two screws
(provided).
3 Slide the assembled tray back into the enclosure, then secure it with
the two screws you previously removed.
Connecting the enclosure to a computer
1 Plug a USB 2.0 cable into the enclosure, then plug the cable into a
USB port on the computer. The operating system automatically
recognizes the new drive.
Note: The enclosure comes with a USB 2.0 Y cable, which has two standard
USB A male-type connectors.
One connector is for data and bus power. The other connector is for additional
power, if required. When you connect the USB 2.0 Y cable to the computer, use
both A male-type connectors to make sure the enclosure has sufficient power.
The operating system automatically detects and sets up the new drive.
2 If the drive is not formatted, please take the steps below to format
the drive.
For Macintosh users:
1 Double-click on Macintosh HD.
2 Click the Applications folder.
3 Click the Utilities folder.
4 Double-click Disk Utility.
5 On the left side of the window, there are the drives connecting
to the computer. Select the drive you want to format and then
click the Erase tab.
6 Verify Volume Format is set to MS-DOS file system, then click
Erase.
For Windows users:
1 Right-click My Computer and select Manage.
2 Click Disk Management on the left pane.
3 Right-click on the drive/device you want to format then select
Format.
4 Occasionally, a warning may come out concerning active
partition, click Yes.
5 Click OK to format.
Installing the backup software
Notes:
• The Roxio BackOnTrack software only runs on Windows Vista,
Windows XP, or Windows 7. computers using USB.
• Connect the hard drive enclosure to your computer before installing
the software.
• Before installing the backup software, make sure that your Windows
operating system has been updated to the latest service pack.
1 Save all files and close all programs.
2 Insert the included CD into the computer. The introductory screen
appears automatically. If the screen does not appear, double-click
the autorun.exe file on the CD.
3 Click Install Roxio® BackOnTrack™ 3 LE. The Welcome screen opens.
4 Click Next to begin the installation.
5 Follow the instructions in the setup wizard, then click Next to
continue.
6 Click Finish to finalize installation.
7 See the User Guide located on the CD for information on using the
software.
Disconnecting the enclosure from your computer
For Windows users:
1 Right-click the Hotplug icon (located near the clock on the taskbar).
2 Select the device you want to unplug, then click STOP.
3 When Windows notifies you that it is safe to do so, unplug the
enclosure from your computer.
For Macintosh users:
1 Drag the USB icon into the TRASH.
2 Unplug the enclosure.
One-year limited warranty
Visit www.rocketfishproducts.com for details
© 2009 Best Buy Enterprise Services, Inc. Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
Contenu du carton
• Boîtier RF-PHD25 • Étui de transport
• Câble en Y USB 2.0 à haut débit • Vis (4)
• CD avec l’application de sauvegarde Roxio • Tournevis
BackOnTrack et le Guide de l’utilisateur • Guide d’installation rapide
Configuration système requise
Un port USB
Windows
MD
7, Windows Vista
MD
, Windows
MD
XP ou Mac OS 10.2.0 ou supérieur.
Installation du disque dur dans le boîtier
1 Retirer les deux vis du panneau arrière, puis extraire le plateau du boîtier.
2 Placer un disque dur formaté sur le plateau, connecter le connecteur de
données au connecteur correspondant de la carte du boîtier, puis
retourner le boîtier et fixer le disque dur à la plaque métallique à l’aide
des deux vis (fournies).
3 Replacer le plateau assemblé dans le boîtier, puis le fixer avec les deux
vis retirées précédemment.
Connexion du boîtier à l’ordinateur
1 Brancher un câble USB 2.0 sur le boîtier, puis brancher le câble sur un
port USB de l’ordinateur. Le système d’exploitation reconnaît
automatiquement le nouveau disque.
Remarque : le boîtier est fourni avec un câble USB en Y, qui a deux connecteurs
standard USB A de type mâle.