Filter
Top Products
FCC DECLARATION OF CONFORMANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
CLASS B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
WWW.SEAGATE.COM
Visit us at our Support pages for assistance with
• Installation:
Additional instructions and troubleshooting assistance
• Knowledge Base: FAQ’s, How to use this product
• Download Center: Installation software, utilities, and diagnostics
• Warranty Information
• And all of your other storage needs
A soft copy of your comprehensive User Guide is included with your product.
To contact Support, visit us at our Contact Us page.
?
KIT CONTENTS
INSTALL DRIVER
CONNECT KIT
USB 3.0
Cable
Seagate
®
BlackArmor
®
PS 110 Drive
USB
Power Cable
USB 3.0
PC Card Adapter
INSTALL BACKUP SOFTWARE
RECOMMENDED: Create Recovery CD
Be sure to create a system recovery CD using
BlackArmor Backup Software. Your system and
data can be restored using this CD. See the
BlackArmor
®
Backup User Guide for instructions.
When disconnecting the drive, ensure that
you use the safely remove hardware feature.
Right-click the safely remove icon in the
notification area and then follow the instructions.
If the installation does not begin
automatically, double-click Setup.exe
on your BlackArmor PS 110 drive or visit
http://support.seagate.com/autorun
for additional instructions.
NOTE: The optional BlackArmor Backup
software can be installed at any time.
QUICK START GUIDE
©2009 Seagate Technology LLC. All rights reserved. Seagate, Seagate Technology, the Wave
logo, and BlackArmor are trademarks or registered trademarks of Seagate Technology LLC or
one of its affiliated companies in the United States and/or other countries. All other trademarks
or registered trademarks are the property of their respective owners. The export or re-export
of hardware or software containing encryption may be regulated by the U.S. Department of
Commerce, Bureau of Industry and Security (for more information, visit www.bis.doc.gov).
Seagate reserves the right to change, without notice, product offerings or specifications.
PN: 100599563 11/09
Seagate Technology LLC
920 Disc Drive
Scotts Valley, CA 95066
U.S.A.
www.seagate.com
1. Connect the USB 3.0 cable to the BlackArmor
®
PS 110 drive and to a USB port on your
computer.
Complete steps 2 and 3 if the driver does not automatically install.
2. Navigate to the BlackArmor PS 110 drive location (Computer > BlackArmor Drive >
USB 3.0 PC Card Adapter)
3. Double-click PC Card Adapter Driver.exe to install the USB 3.0 driver.
4. Once the USB 3.0 driver is installed, safely remove (disconnect) the PS 110 drive from
your computer. (Keep the cable connected to the drive.)
After drive is connected, software
installer automatically launches.
Follow the on-screen instructions.
1
2
3
Connect the USB power cable’s DC plug
to the USB 3.0 PC Card Adapter and to
a USB port on your computer. The LED
on the USB 3.0 PC Card Adapter turns
red to indicate that it is not ready for the
PS 110 drive to be connected.
Insert the USB 3.0 PC Card Adapter
into your computer’s ExpressCard™
slot. The LED turns green to indicate
that the PC Adapter Card is now ready
and has sufficient power.
Connect the USB 3.0 cable (attached to
the PS 110 drive) to the USB 3.0 PC
Adapter Card port.
1
3
2
100599563_PS110_US_QSG.indd 1 11/23/09 3:03:00 PM
Print Date:2010-Jan-6 14:29:40 CST Released; Prod Rel; A; 100599563 Seagate Confidential