Filter
Top Products
1. INTRODUCTION
Skylink
®
Wireless Switch Receiver
Model SW-18R
In this package, you will find a wireless switch receiver.
You can add up to 15 transmitters as you want to control
the same receiver. Simply program the transmitters to the
receiver. Skylink
®
offers Keychain Transmitter Model 18T4
to w ork with your receiver. For more information, please visit
our website at www.skylinkhome.com or contact us.
6. ADDITIONAL TRANSMITTER
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
9. WARRANTY
10. CUSTOMER SERVICE
7. CAUTION
8. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY.
CAUTION : NOT FOR USE WITH DIMMER. DISCONNECT POWER BEFORE
SERVICING.
Maximum Rating :
Input : 120VAC 60Hz
Resistive : 8A (960W)
Incandescent : 300 watts
Motor Load : 1/3 HP
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ section at www.skylinkhome.com , or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm
EST. Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101A293-001 Rev.1
©2005 SKYLINK GROUP
Wireless Switch
Receiver
3. PROGRAM A TRANSMITTER TO THE RECEIVER
5. OPERATION
To activate the receiver, simply press the appropriate button on the
transmitter, it will activate the plugged in device. Pressing it again will turn
off the plugged in device.
2
1
3
4
5
Plug the receiver into a powered,
120VAC electrical outlet inside your
house. (Note: This receiver is designed
to be used indoor only. Do not use this
receiver in an outdoor environment.)
Once the receiver is plugged into an
electrical outlet, the red LED on the front
of the unit will be “on” indicating the unit
is in standby mode.
Plug in the light fixture or small appliance
that you would like to control into the
receiver, as shown.
If there is a power switch on the plugged
in light fixture or small appliance, please
turn it on. The receiver is ready to be
activated.
1
2
3
4
2. INSTALLATION
Button A
Button B
Learn
Button
Button A
Button B
Button C
Button D
4. REMOVE TRANSMITTER FROM THE RECEIVER
Model 18TN
Model 18T4
You need to do the programming in order to add a transmitter to the
receiver.
Plug the receiver into an electrical socket.
Press and hold the learn button on the left hand side of the receiver.
The red LED on the receiver will flash.
Simultaneously, press your assigned button of transmitter 18TN
(either button A or B) or transmitter 18T4 (either button A, B, C or D)
you want to program to the receiver.
The receiver red LED will go off indicates the programming is
completed.
To program the transmitter to control another receiver, repeat
process (1) to (4) but pressing another button.
You can delete the transmitter from a receiver.
Unplug the receiver from the electrical socket.
Pr ess and hold the learn button on the left hand side of the receiver
when plugging the receiver into an electrical socket, the red LED on the
receiver will flash rapidly. All the transmitters are deleted.
2
1