Filter
Top Products
Quick Start Guide
APV10US / 410-0571-001AFeatures and specifications subject to change without notice. © 2006, Targus Group International, Inc. and Targus, Inc., Anaheim, CA 92806 USA.
Product Registration
Targus recommends that you register your Targus accessory shortly after purchasing it. To register your Targus accessory, go to: http://www.targus.com/registration.asp
You will need to provide your full name, email address, phone number, and company information (if applicable).
Warranty
Targus warrants this product to be free from defects in materials and workmanship for one years. If your Targus accessory is found to be defective within that time, we will promptly repair or replace
it. This warranty does not cover accidental damage, wear and tear, or consequential or incidental loss. Under no conditions is Targus liable for loss of, or damage to a computer; nor loss of, or
damage to, programs, records, or data; nor any consequential or incidental damages, even if Targus has been informed of their possibility. This warranty does not affect your statutory rights.
Regulatory Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
FCC Statement
Tested to Comply
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not authorized by the party responsible for compliance could void the user’s authority to operate this product
Declaration of Conformity
Hereby, Targus Group International, declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Press
DC
ai r
DC
auto
AC output
USB Output
(DC power only)
Technical Support
For technical questions, please visit:
US
Internet: www.targus.com/support.asp
Australia
Internet: www.targus.com/au
Email: infoaust@targus.com
Telephone: 1800-641-645
New Zealand
Telephone: 0800-633-222
R32098
TÜV
Rheinland
Product Safety
This inverter is fitted with a spade type 32Vdc
15A fuse. Once the fuse blows, replace with a
same specification and type fuse. Usage of
another type fuse or metal wire will cause
abnormal overheating or even fire hazards.
DC In-Auto connector
DC In-Air connector (for airline compatibility, go to Web site below)
http://www.targus.com/
Electrical Ratings:
Input: 12-16Vdc
AC Output: 120Vac 60 Hz
(modified sinewave)
100W continuous (150W surge)
USB Output: 5Vdc 500mA
Note: When replacing the fuse, please make sure that
all the electrical device(s) are turned off and the power
cables are unplugged. Make sure the fuse is replaced
correctly and before reconnecting the device(s).
Hypertronics to CLA auto/air adapter
Typical Usage
This listing is for reference purpose only. Some
devices exceed the wattages listed. Before using the
device, please refer to the owner’s manual for actual
wattage required.
Play Station 10 Watt
Cellular Phone Charger 25 Watt
Portable Color Printer 30 Watt
Hi-Fi 4 head Stero VCR 40 Watt
13” color TV 70 Watt
Notebook computer 50 Watt
CD player 85 Watt
Work Light 100 Watt
Trouble Shooting
Problem: Lack of Power Output
Possible causes and suggestions:
• Inverter not adequately warmed up
Reconnect the cables and make sure the plugs are secure
• Automotive system requires ignition to be “ON” position
Turn the ignition to “accessory” position
• Battery voltage is below 10 volts
Recharge or replace the battery
• Equipment being operated draws too much power
Reduce load to maximum 100 watts
• Inverter in thermal shut down condition
Allow the inverter to cool down. Ensure there is ventilation around the
unit.
Problem: Low Output Voltage
Possible cause and suggestions:
• Using an average - reading voltmeter
Use true RMS reading meter
• Inverter is overloaded
Reduce the load to a maximum 100 watts to maintain regulation
• Input voltage below 10 volts
Keep input voltage above 10 volts to maintain regulation
100W Auto/Air®
Mobile Power Inverter
Slimline Style
WARNINGS
Any electric appliance with the power consump-
tion beyond 100W is not allowed for usage.This
inverter is not recommended for use with
inductive loads, such as fluorescent lamps or
pumps and most heat generation equipment
such as hair dryers, coffee makers, irons, heaters
and toasters. Otherwise, permanent damage to
the unit and excessive overheating may result.
Fuse
CAUTIONS
If the external cable of this inverter is damaged, stop
using this and contact the authorized agent to replace it to
avoid hazard.
Regularly check input and output connections are tight.
Loose connections can generate harmful heat and / or
damage the inverter or power source. Prevent shock
hazard.
WARNINGS
CAUTIONS
Power / Fault Indicator
This light will flash (blue color) if the
inverter encounters problems.
LED is ON – Normal operation.
LED is flashing – Low voltage
warning signal indicates the supply
voltage is low.
LED is OFF – Unit is off and no
power is being output. Either the
inverter is not plugged into a powered
socket or it has gone into protection
mode due to overheating, overvoltage,
overloading or short circuit.
• Do not block or cover any louvered vents . Place
the inverter on a flat surface with good ventilation
between 0-35
o
C and ideally 15-25
o
C.
• Do not place the inverter on or near a heating
vent or any piece of heat generating equipment.
Keep inverter away from direct sunlight, if at all
possible.
• Do not allow water or other liquids to come into
contact with the inverter.
Ventilation openings
WARNING