Viking InterWorks PCG-729C Personal Computer User Manual


 
The Sony VAIO PCG-705C comes standard with 16MB of removable memory. It can be
expanded to a maximum of 128MB* by installing the following Viking Components
memory options into its two available expansion slots.
The Sony VAIO PCG-707C, PCG-717C, PCG-719C and PCG-729C come standard with
32MB of removable memory. They can be expanded to a maximum of 128MB* by
installing the following Viking Components memory options into their two available
expansion slots.
The Sony VAIO PCG-731 and PCG-735 come standard with 32MB or 64MB of removable
memory. They can be expanded to a maximum of 256MB* by installing the following
Viking Components memory options into their two available expansion slots.
The Sony VAIO PCG-748 comes standard with 32MB of removable memory. It can be
expanded to a maximum of 256MB* by installing the following Viking Components
memory options into its two available expansion slots.
Description Viking P/N
32MB SDRAM Memory Module SNY732, RSNY732
64MB SDRAM Memory Module SNY764, RSNY764
128MB SDRAM Memory Module† SNY7128, RSNY7128
*Requires the removal of all standard memory.
†Available for models PCG-731,PCG-735 and PCG-748 only.
Caution:
Electro Static Discharge (ESD) can damage electronic components. Before touching the mem-
ory module,ensure that you are discharged of static electricity by touching a grounded metal
object.
INSTALLATION INSTRUCTIONS:
1.Turn the computer off and disconnect the AC power supply and any other cables from
the unit.
Note: If the unit appears to be powered down, ensure that it is not in Suspend
mode.
2.Turn the computer upside-down. Remove the battery from the system. If you are not
familiar with this procedure,please refer to your computer’s “Owner’s Manual.”
3. Locate the memory expansion cover on the bottom panel. Also locate the holding
screw securing the cover to the bottom panel. Remove the screw with a small Phillips
screwdriver. Then remove cover by lifting up.
4.Locate the two memory expan-
sion slots in the open compart-
ment. Notice the location of the
off-center key on each of the
expansion slots. One expansion
slot will be occupied with the
standard memory module.
5.If you wish to remove this memory module and replace it with a higher capacity mod-
ule, please continue with this step. If you do not need to remove a memory module,
please proceed to step 6. To remove a
memory module, locate the retaining
clips on both sides of the memory
module. Gently pull both clips away
from the module, then lift the module
out of its expansion slot.
6.To install a memory module, insert the
module into the expansion slot at an
angle and then push it down until it clicks
into place. To be certain that the module
is installed correctly, ensure that the off-
center notch on the module is aligned
with the off-center key of the expansion
slot. The module can only be installed
one way due to the position of the notch.
7.Replace the expansion cover and be sure to secure its holding screw.
8.Replace the battery back into its compartment and turn the system right-side up.
9.Replace the AC power supply and any other cables you may have disconnected.
10. Open the display screen and turn the system on. The computer will automatically
reconfigure itself to recognize the newly added memory. The new memory can be veri-
fied during the POST routine at start-up and at the SETUP utility.
The installation is now complete.
WARRANTY & DISCLAIMERS:
All Viking Components products have been thoroughly tested free of defects in material and workman-
ship. If any malfunction should occur while using one of our products in its recommended environment,
Viking,at its option,will repair or replace the product at no charge,provided the product or any part there-
of has not been abused,misused, neglected,replaced, repaired or modified. Viking shall make the final
determination as to the existence and the cause of any defect. Viking will not repair or replace products
designated as having a “Limited Lifetime”which fail solely because their estimated life has expired. No war-
ranty is made with respect to customer products produced to original purchaser specifications except as
specifically stated in writing by Viking.
All shipping costs shall be the responsibility of the purchaser.
Except as provided herein,there are no express or implied warranties of merchantability or fitness for a par-
ticular purpose. Under no circumstances will Viking Components be liable in any way to the purchaser for
any damages,including but not limited to lost revenue,lost wages,or any other incidental or consequen-
tial damages arising out of the use of or inability to use this product. Viking reserves the right to make
modifications in both hardware and software without prior notifications.
All Viking Components are 100% guaranteed compatible with the OEM machines for which they are
designed. All OEM's names,trademarks and part numbers are used for identification purposes only,and in
no way imply that any of our products are original equipment parts.
Sony and VAIO are a registered trademarks of Sony Electronics Inc.
Product names mentioned herein may be trademarks or registered trademarks of their respective compa-
nies.
Copyright 1999 Viking Components,Inc.
VIKING MEMORY
Manual No.1005206
Release 04/99,Rev.D
SONY
®
VAIO PCG-705C,PCG-707C,PCG-717C,PCG-719C,PCG-729C, PCG-731,
PCG-735,PCG-748
SPEED • POWER • PERFORMANCE
®
INSTALLATION GUIDE