Filter
Top Products
-5-
MPG-68K PG Board (100K) 4-Axis Output, 8-Origin Input
[Characteristics]
This is a board equipped with 4-axis simultaneous-control pulse generation. By an interpreter
(ADVFSC
®
) installed on MPC-68K, programming is possible in a BASIC-like environment.
The maximum pulse rate is 100 kpps (for 3-axis simultaneous interpolation). One MPC-68K
can support about three MPG-68K boards. If a power source unit (MPS-324) is added, about
six boards can be supported.
[Specification]
Power source: DC 12V~24V (for I/O control). Battery retained for 5 years (w/o external
power supply at room temperature).
Pulse output: 4-axis/RS422 specification (photoisolated).
CPU: TMP68301F-16 16MHz. 1M SRAM*2 + 1M PROM*2.
Control I/O: 4-axis output, 8-point origin sensor input.
Consumed current: 150 mA
[Accessories] (1) Power connector (H4P-SHF-AA) JST *1
(2) Contacts (BHF-001T-0.8SS) JST *4
(3) Connector (HIF-3BA-16D-2.54R) Hirose *1
MOP-048 48-Point Transistor Output Board 48 Outputs
[Characteristics]
This is a dedicated output board equipped with 48-point output. Each output is equipped with
an LED monitor. The output interface is an open collector output using a TD62004, where the
control current is 100 mA per one output. Therefore, relays and compact solenoids for air-
pressure control can be connected as they are. Also, because it functions even with 5 V, it can
be used as a TTL output interface. Addresses can be specified by DIP switches (full decoding).
MPC-68K supports up to eight MOP boards.
[Specification]
Power source: DC 5V~24V (for I/O control). 48-point open collector output.
Consumed current: 80 mA
[Accessories] (1) Power connector (H4P-SHF-AA) JST *1
(2) Contacts (BHF-001T-0.8SS) JST *4
MIP-048 48-Point Photocoupler Input Board 48 Inputs
[Characteristics]
This is a dedicated input board equipped with 48-point input. Each input is equipped with an
LED monitor. The input interface is a photocoupler input using a TLP-521, where the control
current is 2 mA per one input. Also, because it functions even with 5 V if the resistor array is
exchanged, it can be used as a TTL input interface. Addresses can be specified by DIP switches
(full decoding). MPC-68K supports up to eight MIP boards. MIP-048 is equipped with a
resistor socket for two-line sensor compatibility.
[Specification]
Power source: DC (5V) 12V~24V (for I/O control). 48-point optocoupler input.
* If used with DC 5V, the resistor array needs to be replaced.
Consumed current: 30 mA
[Accessories] (1) Power connector (H4P-SHF-AA) JST *1
(2) Contacts (BHF-001T-0.8SS) JST *4
*Current values indicate standard consumed current TYP values. Please keep 20~50 % room in designing.
*Current values indicate consumed current of the internal DC 5V power source, and the maximum current values with all I/Os
ON for the I/O boards.
*[] Current values indicate externally-supplied DC 24V current, and the minimum current values with all I/Os OFF.
(1)
(2)
(3)
(1)
(2)
MOP-048
ACCEL CORP
CEP-013B
(1)
(2)