Filter
Top Products
TOTAL ACCESS OPTI-T200
PRICING AND AVAILABILITY 800.827.0807
TECHNICAL SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
www.adtran.com
61184400L1-22A
ACCOUNT PROVISIONING
1. Account 1
a) User Name – User Defined, up to 15 characters
b) Password – User Defined, up to 15 characters
c) Permission Level – Disabled, Read Only, Read-Write, Administrator
d) Delete Account
2. Account 2 – Same options as Account 1
3. Account 3 – Same options as Account 1
4. Account 4 – Same options as Account 1
5. Account 5 – Same options as Account 1
6. Account 6 – Same options as Account 1
7. Account 7 – Same options as Account 1
8. Account 8 – Same options as Account 1
9. Account 9 – Same options as Account 1
10. Account 10 – Same options as Account 1
SOFTWARE UPGRADE
Software download for the local OPTI-T200 is provided using XModem or YModem via the craft port
or TFTP, XModem or YModem via Ethernet. Software download to a remote OPTI-T200 is
accomplished either from the CO OPTI-T200 craft port or its Ethernet port. The download is carried
over the DCC channel. TFTP is supported from only the Ethernet interface, and both systems would
require IP addresses.
COMPLIANCE
This product intended for use in Restricted Access Areas only, and is intended to be installed in a Type
“B” or “E” enclosure. This product complies with UL 60950.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or
modifications not expressly approved by ADTRAN could void the user’s authority to operate this
equipment.
WARRANTY
ADTRAN will replace or repair this product within the warranty period if it does not meet its
published specifications or fails while in service. Warranty information can be found at
www.adtran.com/warranty. U.S. and Canada customer Faxback: 877-457-5007, Document 414.
Code Input Output
Power Code (PC) F C
Telecommunication Code (TC) – –
Installation Code (IC) A –
PROVISIONING OPTIONS
Upon initial installation, the OPTI-T200 uses factory default settings. To provision the
OPTI-T200, connect a terminal emulator via the RS-232 (DB-9) connector on the front
panel. The terminal must be VT100 compatible and set for 9600 bps, 8 data bits, no parity
and 1 stop bit. The following table lists the provisioning settings and their default values.
The settings are retained in a nonvolatile memory device in case of power loss to the
OPTI-T200.
Options Settings (Default in Bold)
Service State In Service, Out Of Service-Unassigned, Out Of Service-Maintenance
DS3 Provisioning
DS3 Interface Enable, Disable
DS3 Line Build Out Short, Long
Signal Fail (SF) Thresh 1x10
-3
, 1x10
-4
, 1x10
-5
Signal Degrade (SD) Thresh 1x10
-5
, 1x10
-6
, 1x10
-7
, 1x10
-8
, 1x10
-9
Clock Source (TX) 1. Receive OC-3
2. Free Run
CLLI Code User definable up to 20 characters
Network Provisioning
IP Address User Defined
Format = x.x.x.x where x = 0–255
Subnet Mask User Defined
Format = x.x.x.x where x = 0–255
Default Gateway User Defined
Format = x.x.x.x where x = 0–255
Telnet Menu Port User defined = 0–65535 (23)
Telnet (TL-1) Port User defined = 0–65535 (2001)
Time and Date User Defined
Mount Location Central Office, Remote
Account Provisioning See the Account Provisioning section to the right of this table.
Restore Factory Defaults
Software Upgrade TFTP, XModem, YModem
NOTE: To navigate through the menus, select the desired entry and press Enter. To work
backward in the menus, press the Escape key. Some entries can be changed in only
the Out-of-Service – Maintenance mode.