Filter
Top Products
EKI-7758F User Manual 36
systemlog mode
[client|server|both]
G
Specified the log mode switch(config)# systemlog mode both
show systemlog E Displays system log. Switch>show systemlog
show systemlog
P
Show system log client & server
information
switch#show systemlog
no systemlog G Disable systemlog functon switch(config)#no systemlog
smtp enable G Enable SMTP function switch(config)#smtp enable
smtp serverip
[IP address]
G
Configure SMTP server IP switch(config)#smtp serverip 192.168.1.5
smtp authentication G Enable SMTP authentication switch(config)#smtp authentication
smtp account
[account]
G
Configure authentication account switch(config)#smtp account User
smtp password
[password]
G
Configure authentication password switch(config)#smtp password
smtp rcptemail
[Index] [Email address]
G
Configure Rcpt e-mail Address switch(config)#smtp rcptemail 1 Alert@test.com
show smtp P Show the information of SMTP switch#show smtp
no smtp G Disable SMTP function switch(config)#no smtp
event device-cold-start
[Systemlog|SMTP|Both]
G
Set cold start event type switch(config)#event device-cold-start both
event authentication-failure
[Systemlog|SMTP|Both]
G
Set Authentication failure event
type
switch(config)#event authentication-failure both
event X-ring-topology-change
[Systemlog|SMTP|Both]
G
Set X - ring topology changed
event type
switch(config)#event X-ring-topology-change both
event systemlog
[Link-UP|Link-Down|Both]
I
Set port event for system log switch(config)#interface fastethernet 3
switch(config-if)#event systemlog both
event smtp
[Link-UP|Link-Down|Both]
I
Set port event for SMTP switch(config)#interface fastethernet 3
switch(config-if)#event smtp both
show event P Show event selection switch#show event
no event device-cold-start G Disable cold start event type switch(config)#no event device-cold-start
no event authentication-failure
G
Disable Authentication failure
event type
switch(config)#no event authentication-failure
no event X-ring-topology-change
G
Disable X - ring topology changed
event type
switch(config)#no event X-ring-topology-change
no event systemlog
I
Disable port event for system log switch(config)#interface fastethernet 3
switch(config-if)#no event systemlog
no event smpt
I
Disable port event for SMTP switch(config)#interface fastethernet 3
switch(config-if)#no event smtp
show systemlog
P
Show system log client & server
information
switch#show systemlog
3.1.16 SNTP Commands Set
Table 3.16: SNTP Commands Set
Netstar Commands Level Description Example
sntp enable
G
Enable SNTP function switch(config)#sntp enable
sntp daylight
G
Enable daylight saving time, if
SNTP function is inactive, this
command can’t be applied.
switch(config)#sntp daylight
sntp daylight-period
[Start time] [End time]
G
Set period of daylight saving time,
if SNTP function is inactive, this
command can’t be applied.
Parameter format:
[yyyymmdd-hh:mm]
switch(config)# sntp daylight-period 20060101-
01:01 20060202-01-01
sntp daylight-offset
[Minute]
G
Set offset of daylight saving time, if
SNTP function is inactive, this
command can’t be applied.
switch(config)#sntp daylight-offset 3
sntp ip
[IP]
G
Set SNTP server IP, if SNTP
function is inactive, this command
can’t be applied.
switch(config)#sntp ip 192.169.1.1
sntp timezone
[Timezone] G
Set timezone index, use “show
sntp timzezone” command to get
more information of index number
switch(config)#sntp timezone 22
show sntp P Show SNTP information switch#show sntp