Allied Telesis AT-CM3K0S Network Card User Manual


  Open as PDF
of 2
 
4 5 6
3. Secure the line card in the chassis by tightening the captive-screw with a Phillips
head screwdriver.
4. Remove the dust cover from the SFP slot.
5. Slide the SFP module into the slot until it clicks into place.
6. Remove the dust cover from the fiber optic port on the SFP module.
7. Connect the fiber optic cable to the port on the SFP module.
8. Connect a twisted pair cable to the RJ-45 twisted pair port on the line card.
LEDs
The RDY (Ready) LED displays general status information.
The operating mode of the line card is displayed by the SML, ML and OAM LEDs.
The SFP slot has three LEDs.
The 10/100/1000Base-T twisted pair port has five LEDs.
Note
For more information on the Link LEDs, refer to the explanation of the media
converter operating modes in the Converteon AT-S73, AT-S99, and AT-S102
Management Software User’s Guide.
ECO Friendly Button
The recessed ECO Friendly button on the front panel of the line card is used to toggle the
low power mode, which controls the LEDs. You can use the button to turn off the LEDs to
conserve power when you are not monitoring them. To toggle the LEDs on or off, press
the recessed button with a pointed object, such as the end of a straightened paperclip.
You can also toggle the low power mode with the AT-CV5M02 Management Card. The
low power mode does not affect the network operations of the line card or control the
RDY LED.
Default Settings
The default settings for the media converter are listed here.
Technical Specifications
Electrical, Safety, and Emissions Statements
Standards: This product meets the following standards when installed in compliant host equipment.
Emission FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CE
Immunity EN55024
Electrical Safety UL60950-1 (
c
UL
us
), EN60950-1 (TUV), CAN/CSA C22.2 No. 60950-1
Copyright © 2008 Allied Telesis, Inc. All rights reserved. No part of this publication may be
reproduced without prior written permission from Allied Telesis, Inc. www.alliedtelesis.com.
LED State Status/Operating Mode
RDY
(Ready)
Off The line card is initializing the AT-S102 Management Software,
which takes approximately one minute, or the card is not receiving
power.
Green The line card has initialized its management software and is ready to
transfer network traffic.
Operating Mode
LEDs
SML
(Smart
MissingLink)
ML
(Missing Link)
OAM
(Operations,
Administration
and
Maintenance)
Link Test mode Off Off Off
Link Test mode with OAM Off Off On
MissingLink mode Off On Off
MissingLink mode with OAM Off On On
Smart MissingLink mode On Off Off
Smart MissingLink mode with OAM On Off On
LED Color Description
LK
(Link)
Off The fiber optic port on the SFP transceiver has not formed a link
with the remote device.
Green The port has formed a link with the fiber port on the remote device.
Blinking
Green
The media converter is operating in the Smart MissingLink mode
and the twisted pair port has not formed a link with a network device.
AT
(Activity)
Off The port is not connected to a fiber optic cable, has not formed a link
with the remote device, or is not receiving or transmitting packets.
Blinking
Green
The fiber optic port on the SFP module is receiving or transmitting
network packets.
1000M Off The SFP module is 100Base-FX.
Green The SFP module is 1000Base-X.
LED Color Description
LK
(Link)
Off The port has not formed a link with a network device.
Green The port has formed a link with a network device.
Flashing Green The media converter is operating in the Smart MissingLink
mode and the fiber optic port on the SFP module has not
formed a link with a network device.
AT
(Activity)
Off The port is not receiving or transmitting network packets.
Blinking Green The port is receiving or transmitting network packets.
FD
(Full
duplex)
Off The port is operating in half-duplex mode.
Green The port is operating in full-duplex mode.
1000M
and
100M
100M - Off
1000M - Off
The port is operating at 10 Mbps.
100M - On
1000M - Off
The port is operating at 100 Mbps.
100M - Off
1000M - On
The port is operating at 1000 Mbps.
Feature Default Setting
Basic Settings
Operating Mode Link Test
Maximum Frame Size 10240 bytes
Twisted Pair Port Auto-Negotiation with auto-MDI/MDI-X
Ingress and Egress Filtering None
Low Power Mode Disabled
Operating Mode DIP Switches Enabled
OAM Settings
Admin State Enabled
Mode Passive
Maximum OAMPDU Size 1518 bytes
Loopback Support Enabled
Variable Retrieval Support Enabled
Physical and Environmental
Dimensions (H x W x L) 22 mm x 73 mm x 130 mm
(.86 in. x 2.9 in. x 5.1 in.)
Weight 113 grams (0.25 lb.)
Operating Temperature 0° C to 40° C (32° F to 104° F)
Storage Temperature -25° C to 70° C (-13° F to 158° F)
Operating Relative Humidity 5% to 90% RH (non-condensing)
Storage Relative Humidity 5% to 95% RH (non-condensing)
Operating Altitude Range Up to 3,048 m (10,000 ft.)
MTBF 1,530,000 hours
Optical
Connector Type SFP
Operating Speed 100 Mbps or 1000 Mbps (fixed speed)
Fiber Type SFP Transceiver
Electrical Ratings
Power Consumption 8.5 Watts maximum
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant
to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right
to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada.
Warning
In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Feature Default Setting
 previous