Filter
Top Products
Turn the sheet over.
LX0142001
USA/CAN
Printed in China
Before you can use the machine, read this Quick Setup Guide
for the correct setup and installation.
Quick Setup Guide
DCP
-
385C
Important
DO NOT
connect the
USB cable yet.
a. The LCD shows:
No Cartridge
Black
Install Ink
b. Open the ink cartridge cover a.
3
Install the ink cartridges
4
d. Unpack the ink cartridge.
Turn the green knob on the protective yellow cap clockwise until it clicks to release the
vacuum seal, then remove the cap a.
If all lines are clear and visible, press o
(Yes) to finish the quality check.
If you can see missing short lines, press o
(No) and follow the steps on the LCD.
Connect the power cord
Set the LCD contrast (If needed)
7
5
Check the print quality
c. Remove the green protective
part a.
a. When the preparation process
has finished, the LCD shows
this message.
Set Paper and Press
Start
Press Color Start.
OK
Poor
Set the date and time
8
a. Press Menu.
b. Press a or b to choose
General Setup.
Press OK.
c. Press a or b to choose
LCD Settings.
Press OK.
d. Press a or b to choose
LCD Contrast.
a. Press Menu.
b. Press a or b to choose
Initial Setup, and then
press OK.
c. Press a or b to choose
Date&Time, and then press OK.
b. Check the quality of the four color
blocks a on the sheet.
(black/yellow/cyan/magenta)
d. Press a or b repeatedly to enter the last
two digits of the year, and then press OK.
Date&Time
Year:20
08
MENU Input & Press OK
(e.g. Enter 08 for 2008.)
6
Set the language (If needed)
a. Press Menu.
b. Press a or b to choose Initial Setup.
Press OK.
c. Press a or b to choose Local Language.
Press OK.
d. Press a or b to choose your language.
Press OK.
e. Press Stop/Exit.
e. Repeat for Month and Day, and Hours and
Minutes in 24-hour format.
f. Press Stop/Exit.
Note
If you make a mistake and want to start
again, press Stop/Exit to go back to step a.
e. Press d or c to choose Light, Med or Dark.
Press OK.
f. Press Stop/Exit.
Note
You can also adjust the angle of the display by
lifting it.
WARNING
Warnings tell you what to do to
prevent possible personal injury.
Plastic bags are used in the packaging of your
machine. To avoid danger of suffocation, please
keep these bags away from babies and children.
WARNING
Start Here
Unpack the machine and check the components Load plain Letter/A4 paper
12
a. Pull out the paper tray.
b. Lift the paper tray cover a.
c. Press and slide the
paper side guides
a and paper length
guide b to fit the
paper size.
Make sure that the
triangular marks c
on the paper side
guides a and paper
length guide b line
up with the mark for
the paper size you
are using.
Important
Do not push the paper
in too far.
d. Fan the stack of paper well.
e. Gently put the paper into the paper tray.
Check that the paper is flat in the tray.
Note
When you use Legal size paper, press and hold the
universal guide release button
a as you slide out the
front of the paper tray.
1
g. Close the paper tray
cover and slowly push
the paper tray back into
the machine.
h. Pull out the paper
support a until it clicks,
and then unfold the
paper support flap b.
f. Gently adjust the paper side guides to the paper with both hands.
Make sure the paper side guides touch the edges of the paper.
a. Connect the power cord.
Important
DO NOT connect the
USB cable yet.
Note
The control panel
warning LED will stay on
until you have installed
the ink cartridges.
e. Install each ink cartridge in the direction of the arrow
on the label.
Take care to match the color of the lever a with the
cartridge color b.
Note
The components of your box may differ •
depending on your country.
Save all packing materials and the box in case •
for any reason you must ship your machine.
A USB cable is not included. •
You need to purchase a USB 2.0 cable that is no
more than 6 feet (2 meters) long.
Your machine has a USB 2.0 Full-speed interface.
This interface is compatible with USB 2.0 Hi-Speed;
however, the maximum data transfer rate will be
12 Mbits/s. The machine can also be connected to
a computer that has a USB 1.1 interface.
a. Remove the protective tape and film.
f. Gently push the ink cartridge until it clicks. After all the
ink cartridges are installed close the ink cartridge cover.
Note
The machine will prepare the ink tube system for printing.
This process will take approximately four minutes.
Do not turn off the machine.
d. Make sure you have all components.
2
Starter Ink
Cartridges [x4]
Black
Yellow
Cyan
Magenta
Accessory
Order Form
CD-ROM
Quick Setup
Guide
User’s Guide
b.
Remove the green protective packing a
by lifting the front of the machine and then
pulling down on the packing part.
1
1
c.
Remove the plastic bag b containing the
ink cartridges from on top of the paper tray.
1
1
1
2
1
1
3
3
2
1
1
2
1
1