Bryant SYSTXBBRWF01 Network Router User Manual


  Open as PDF
of 6
 
6
WiFi B--SAM SETUP 1
AUX: AUX SENSOR
IP TYPE: DHCP
IP: 192.168.100.0
MAC ADDR:
00:01:02:03:04:05
SUBNET MASK:
255.255.255.000
SERVER
STATUS: CONNECTED
<BACK NEXT >
WiFi B--SAM SETUP 2
DEFAULT GATEWAY:
192.168.001.001
DNS SERVER:
061.010.231.015
PORT: 49152
SERVER
STATUS: CONNECTED
<BACK NEXT >
AUX: The auxiliary sensor can be renamed to something meaningful, such as WATER or GENERATOR. Use the Temp +/-- buttons to move
between letters, and the Time +/-- button to choose letters.
IP TYPE: Choose DHCP (default) or STATIC for the Internet addressing type.
IP: Shows the current IP address of the SAM. If IP TYPE is STATIC then this item can be change. Use the Temp +/-- buttons to move
between letters, and the Time +/-- button to choose letters. If IP TYPE is DHCP, the IP address cannot be changed.
MAC ADDR: Shows the MAC Address of the SAM’s network module.
SUBNET MASK: If IP TYPE is STATIC, this can be changed to a different subnet number. Use the Temp +/-- buttons to move between
letters, and the Time +/-- button to choose letters. If IP TYPE is DHCP, the SUBNET MASK cannot be changed.
DEFAULT GATEWAY: If IP TYPE is STATIC, this can be changed to point to a different gateway. Use the Temp +/-- buttons to move
between letters, and the Time +/-- button to choose letters. If IP TYPE is DHCP, the DEFAULT GATEWAY cannot be changed.
DNS SERVER: If IP TYPE is STATIC, this can be changed to point to a different DNS server. Use the Temp +/-- buttons to move between
letters, and the Time +/-- button to choose letters. If IP TYPE is DHCP, the DNS SERVER cannot be changed.
PORT: This can be changed to use a different port through the homeowner’s network. The default is port 49152.
SERVER STATUS: Sho ws status of the SAM connection to Bryant’s servers. If the screen shows NON CONNECTED, please check
network settings or network cable.
Pressing the right side button (for NEXT >) will display the following screen:
WiFi B--SAM WIRELESS 1
SSID:
HOME
CHANNEL: 0
SIGNAL STRENGTH:
JJJjjjjjj
L H
SERVER STATUS: CONNECTED
<BACK NEXT >
WiFi B--SAM WIRELESS 2
ENCRYPTION:
WEP 6 4 BIT HEX
KEY:
ENTER 10 HEX DIGITS
0--9,A--F
<BACK NEXT >
SSID: Enter the name of the homeowner’swireless network using the Temp +/-- and Time +/-- buttons.
CHANNEL: This field determines which frequency to use. It can be left on Channel 0 to search automatically, or adjusted to the one being
used by the homeowner’s wireless router.
ENCRYPTION: This chooses the type of security used by the homeowner’s wireless router. Choose:
S None -- no data encryption
S WEP (Wired Equivalent Privacy) -- use WEP 64 or 128 bit data encryption
S W PA ( WiFi Protected Access Pre--Shared Key ) -- use WPA--PSK standard encryption
KEY: WEP 64 BIT HEX (10 hex digits)
WEP 64 BIT CHARS (5 ASCII characters)
WEP 128 BIT HEX (26 h ex digits)
WEP 128 BIT CHARS (13 ASCII characters)
WPAPSKHEX(8to64hexdigits)
WPA PSK CHARS (8 to 63 ASCII characters)
SIGNAL STRENGTH: Displays the current signal strength of the identified wireless router (SSID). Nine bars is full strength.
CONNECTED means the SAM has connected with the wireless router. NOT CONNECTED will mean either one of the parameters is
incorrect, or the signal strength may be too low.
Manufacturer reservesthe rightto discontinue,or changeat anytime,specifications or designswithoutn otic e andwithout incurring obligations.
E2008BryantHeating&Coo li ng Systems 7310W.MorrisSt. Indianapolis,IN 46231 Printedi n U.S.A. EditionDate: 09/08
Replaces:NEW
Catalog No. IIBBRWF---01
SYSTXBBRWF01
 previous