Canon E-IM-2514 Tablet Accessory User Manual


  Open as PDF
of 2
 
E-IM-2514
Bluetooth Calculator Keypad /
Bluetooth Teclado Calculadora
If the Calculator Keypad is not connected or not functioning properly:
● Check battery placement direction.
● Make sure computer meets the system requirements described.
● Check if Bluetooth hardware and software are installed correctly and enabled.
● Make sure the Bluetooth USB adapter (dongle) is functioning properly.
● Remove obstacles between personal computer and the Calculator Keypad.
● If recently connected (paired) with a different computer, reset the connection to
your current computer by repeating the initial setup (re-pairing).
● If unable to reset the connection to a previously paired computer, remove or delete
the device before re-pairing (please follow your computer’s procedures on how to
remove or delete a Bluetooth device).
● If the display disappears after the Bluetooth is turned ON, press key and
check if the
icon appears.
● Change to new batteries if the icon appears.
● If the “E” icon appears, the keypad is locked. Press or to clear and
resume operation. (The “E” icon occurs when the result or memory content
exceeds 10 digits to the left or when dividing by “0”.)
J Electromagnetic interference or electrostatic discharge
may cause any malfunction. Should this occur, use
the tip of a ball point pen (or similar object) to press
the [CAL RESET] button on the back of the Calculator
Keypad. And turn off and on the Bluetooth Switch.
TROUBLESHOOTING
● When using with a different computer, please pair again using the initial setup.
● The Bluetooth icon will remain on (solid, not ashing) when the Calculator Keypad
is successfully connected to your computer.
● To conserve battery, turn the Bluetooth connection off when travelling or when
using as a calculator only without a computer.
● Bluetooth connection requires battery power to function properly.
● When Bluetooth is off, calculator functions can be used without batteries
(powered by solar panel).
USAGE TIPS
USER GUIDE /
GUIA DE USARIO
PRINTED IN CHINA / IMPRESO EN CHINA
ENGLISH
IMPORTANT: READ BEFORE USE
Please read the following instructions and safety
precautions before using the Calculator Keypad.
Keep this sheet on hand for future reference.
THIS DEVICE IS WINDOWS AND MACINTOSH COMPATIBLE.
You will be prompted during setup to select an operating system (OS) using the
Bluetooth OS switch on the back of the device. If the switch is set to an incorrect
OS, the device may not function properly.
If your computer does not have a built-in Bluetooth device, you need to purchase
a Bluetooth USB adaptor (dongle).
Before connecting the Calculator Keypad with your computer’s Bluetooth device
or dongle, be sure the Bluetooth feature in your computer is enabled and ready.
WINDOWS VISTA
®
AND WINDOWS
®
7
Your computer is now setup to use your Calculator Keypad.
Click “Close” to nish.
5
1
Windows Vista
®
Go to “Control Panel > Bluetooth Devices” and
click on “Add Wireless Device”.
Windows
®
7
Go to “Control Panel > Hardware and Sound > Devices and Printers”
and click on “Add a Device”.
Press the “PAIR” button on
the device using the tip of a
pen or a similar object.
(NOTE: In the computer window, the “Canon X Mark I K”
should appear in the list of new devices. If not, wait a moment
and press the “PAIR” button again -or- move the Bluetooth switch to
“OFF” and then to “PC ON”, and press the “PAIR” button again.)
3
2
To nd the device, move
the Bluetooth switch on the
device to “PC ON”.
(NOTE: The icon
on the front display
should be ashing.)
Select “Canon X Mark I K” and click “Next”.
(NOTE: Wait a moment while the computer connects to the device.
It will take a few seconds for the computer to nish automatically
installing the device. A notication should appear stating that the
device has installed successfully.)
4
Hardware : Bluetooth-enabled (v2.0) computer (with either built-in Bluetooth or
external Bluetooth dongle)
Windows based PC x86 / x64 or above, Intel-based Mac
Operating Windows
®
XP (SP2 or above) or Windows Vista
®
or Windows
®
7
System : Mac OS
®
X 10.4 ~ 10.6
SYSTEM REQUIREMENTS
● Keep the batteries out of reach of children.
● Never expose batteries to high temperatures, direct heat, or dispose by incineration.
● Do not mix new and old batteries or batteries of different types.
● Do not allow metal objects to touch the battery terminals on the device; they can
become hot and cause burns.
● Remove the batteries if they are worn out or have been stored for an extended
period of time.
● Always remove old, weak, or worn out batteries promptly and recycle or dispose of
them in accordance with Federal, State, and Local regulations.
● If a battery leaks, remove all batteries, taking care to keep the leaked uid from
touching your skin or clothes. If uid from the battery comes into contact with skin
or clothes, ush skin with water immediately.
BATTERY CAUTION !
Model : X Mark I Keypad BT
Power Source : AAA-size Alkaline batteries x 2
Wireless Connection : Bluetooth v2.0
Operating Temperature : 0ºC to 40ºC (30ºF to 104ºF)
Dimension : 155mm (L) x 86mm (A) x 20mm (A)
1-7/64” (L) x 3-25/64” (A) x 25/32” (A)
Weight : 140g (4.9 oz) without batteries / 163g (5.7oz) with batteries
DEVICE SPECIFICATIONS
Frequency : 2.4 GHz frequency range
Connection Range : The operating range is up to 10 meters (32.8 feet)
NOTE : Connection range is affected by many factors, such as nearby metallic
objects and the relative positioning of the device and the receiver.
BLUETOOTH SPECIFICATIONS
NOTE: All specications are subject to change without notice.
● Never continue to use the Calculator Keypad if it starts to smoke, emits a strange
odor, or emits heat. Continued use of the calculator under such conditions creates
the danger of re and electric shock.
● When cleaning the Calculator Keypad, do not use a damp cloth or volatile liquid
such as paint thinner; instead, use only a soft, dry cloth.
● Never dispose of the Calculator Keypad improperly (such as burning), which can
lead to personal injury or harm. You should dispose of this product in accordance
with Federal, State, and Local regulations.
HANDLING AND CARE
Screens or set-up may vary depending on the computer or Bluetooth device driver.
Instructions are provided for Windows
®
XP, Windows Vista
®
, Windows
®
7 and Macintosh.
INITIAL SETUP INSTRUCTIONS
1. Remove the battery cover from the back of the Calculator Keypad by sliding the
cover in the direction of the arrow.
2. Install AAA alkaline batteries, matching the positive (+) and negative (–) ends
of each battery with the polarity indicators inside the battery compartment.
3. Place the battery cover back on the battery compartment.
CAUTION: There is a risk of explosion if an incorrect battery type is installed.
Please dispose of used batteries according to their instructions.
BATTERY INSTALLATION
1
2
3
▪ Power on
▪ Clear all display | Keypad lock / unlock
▪ Re-connect the Bluetooth connection
▪ Clear last input entered | Clear all input (CAL mode only)
▪ Escape the input (KP mode only)
▪ Switch between Calculator Mode or Keypad Mode
▪ Backspace in Keypad mode; in Calculator mode shifts each digit of the
displayed numerical value and clears the last signicant digit
▪ Send calculation results or display contents to computer
(CAL mode with Bluetooth Connection)
▪ Perform percentage add-on and discount calculation. (CAL mode only)
▪ Execute calculation (CAL mode only)
▪ Enter Key -- Conrm the input (KP mode only)
▪ Set the number of digits displayed in calculation after the decimal point
▪ Press and then press and hold , the display will change in the
sequence of F 0 2 3 F (CAL mode only)
▪ F represents a oating decimal point
WAKE
UP
KEY INDEX
J The Bluetooth icon ( ) will ash
on and off during the setup
connection process.
J Once the device is successfully
connected to your computer,
the Bluetooth icon ( )
on the
front display will remain solid.
BLUETOOTH ICON
© CANON ELECTRONIC BUSINESS MACHINES (H.K.) CO., LTD. 2011
CALCULATOR MODE AND KEYPAD MODE
When Bluetooth connected, this Calculator Keypad has 2 modes --
Calculator Mode (CAL) and Keypad Mode (KP).
Switch between Calculator and Keypad Mode
J To switch between Calculator and Keypad mode,
simply press the
key.
Calculator Mode (with Bluetooth connection)
J The calculator performs normal 10-digit calculator operations.
J Send calculation results or display contents to a computer by pressing
SEND
.
• You cannot perform a send operation while the E (Error) indicator is shown on
the Calculator Keypad display.
• The
SEND
key is disabled when the calculator is not Bluetooth connected.
Keypad Mode (with Bluetooth connection)
J Input the following to a computer directly:
Numbers 0-9 +
–
× ÷
Auto Power Off and Wake-up
J Calculator Only, NOT Bluetooth Connected
• The device will automatically power off after approximately 7 minutes
of inactivity.
Press the key to turn on the device.
J CAL and KP Modes, with Bluetooth Connection
• The Bluetooth connection will be disconnected after approximately 30 minutes
of inactivity (the display will reset to “0”). The device will function the same as
“Calculator Only, NOT Bluetooth Connected”.
Press
to re-activate the Bluetooth connection.
• After the Bluetooth connection is disconnected, the device will automatically
power off after an additional 7 minutes of inactivity. Press and then
to turn on the device and re-activate the Bluetooth connection.
Power-low Indicator
J When the display is dim or the
icon appears,
replace the batteries to avoid running out of
power unexpectedly.
Keypad Lock (with Bluetooth connection)
J Press the key and hold for 3 seconds to lock.
J To unlock, press the key and hold for 3 seconds.
Keypad mode display
Power-low display
Keypad locked display
1
Your computer is now setup to use your Calculator Keypad.
Click “Quit” in the Conclusion window to nish.
(NOTE: If Keyboard Setup Assistant appears, ignore, and close the window.)
8
Press the “PAIR” button on
the device using the tip of a
pen or a similar object.
(NOTE: In the Bluetooth Setup Assistant, the “Canon X Mark I K”
should appear under the Devices list. If not, wait a moment
and press the “PAIR” button again.)
4
Move the Bluetooth switch on
the device to “MAC ON”.
(NOTE: The icon
on the front display
should be ashing.)
3
Select “Canon X Mark I K” and click “Continue”.
5
Switch to Keypad mode by pressing , will appear on the display.
6
Enter the passkey on the
keypad and press .
(NOTE: Must be in Keypad
mode to enter passkey.)
7
To activate Bluetooth,
go to the Bluetooth icon in
the menu bar and select
“Turn Bluetooth On”.
(NOTE: If already “On”, skip to step 2.)
Go to the Bluetooth icon and select
“Set up Bluetooth Device...”
to open the Bluetooth Setup Assistant.
2
MACINTOSH
®
Enter the passkey or code
on the keypad and press
.
(NOTE: Must be in Keypad
mode to enter code.)
6
Your computer is now setup to use your Calculator Keypad.
(NOTE: The Bluetooth Setup window should automatically close once
the passkey or code is accepted.)
7
1
Open “My Bluetooth Places” and double-click on “Add a Bluetooth
Device” to open the Bluetooth Setup.
Press the “PAIR” button on
the device using the tip of a
pen or a similar object.
(NOTE: In the Bluetooth Device Selection window, “Canon X Mark I K”
should appear. If not, wait a moment and press the “PAIR” button
again -or- move the Bluetooth switch to “OFF” and then to “PC ON”,
click “Search Again” and press the “PAIR” button again.)
3
Select “Canon X Mark I K” and click “Next”.
(NOTE: If asked, “Do you need a passkey to add your device?”,
select “Choose a passkey for me” and click “Next”.)
4
2
To make the device
discoverable, move the
Bluetooth switch on the
device to “PC ON”, then
click “Next” on the computer.
(NOTE: The icon
on the front display
should be ashing.)
Switch to Keypad mode by pressing
, will appear on the display.
WINDOWS
®
XP