Filter
Top Products
Introduction
Congratulations on the purchase of your new CHAUVET Bubble Machine. We are confident you
will enjoy many trouble free hours with this unit. To assist with the care and use of the product we
have prepared this short guide.
Operation
This bubble machine has been designed to function on a mains power supply of either
120V~60Hz or 230V~50Hz and has been fitted with a suitable power plug for use with your local
voltage. Check the label on the unit and the power plug for the correct voltage.
Place the machine on a level surface and loosen the thumbscrew on the front of the unitfor fluid
tank access, see diagram (fig.1). This will allow the whole of the top cover to be lifted revealing
the fluid tank in the base. Fill the tank with quality bubble fluid only. We recommend use of
CHAUVET bubble fluid (BJ-U or BJ-Q) as it has been specially formulated for use with CHAUVET
bubble machines and produces the best results. Replace the cover and tighten screws. Plug into
the mains power supply and stand back in amazement as you fill the area with hundreds of
bubbles!
After use, ensure that all bubble fluid is drained before moving.
Installation / Mounting
The bubble machine must be used in a horizontal position sitting on a level surface or it may be
mounted using the bracket provided ensuring that the bubbles are not shooting directly at
anyone’s face or above areas of heavy traffic as bubble fluid leaves a slippery surface. Whatever
method of installation you choose, the bubble machine must not have more than a 5 degree
angle of inclination. We always suggest that for safety purposes use of a suitable hanging clamp
and safety cable is essential. CHAUVET offers a range of items, which are ideal for safe
mounting.
Mode of Operation
The B-250 accepts a range of Chauvet optional controllers. The mode selector switch on the rear
of the unit has 3 positions: On – Off – Controller. When in the controller setting the fan will
continue to run but the wand wheel will be in standby awaiting a signal from the controller.
Optional Controllers:
FC-4 Timer Remote
FC-5 Wireless Remote
DMX-3 FDMX Converter
To use the selected controller, simple plug into the receptacle on the rear of the B-250.
Cleaning
Cleaning your bubble machine regularly will help reduce costly parts replacement and repair
charges.
After every 40 hours of continuous operation or when the machine will be idle for a long time it is
recommended to rinse the bubble wands and fluid tank with warm water, to prevent a build-up of
residue which could reduce performance.
1. While the unit is unplugged, loosen thumbscrew and lift cover to reveal fluid tank.
2. Empty all bubble fluid from the tank and replace with warm water. Plug unit in and allow to
run as usual, until all wands appear to be free of residue.
3. Cleaning is now complete. Unplug and refill with bubble fluid.
All bubble machines are prone to clogging due to the consistency of bubble fluid. However a well
maintained machine should provide years of reliable use. The body of the unit may be cleaned
with a soft damp cloth. Store dry.
Maintenance & Servicing
Do not allow bubble fluid to become contaminated. Always replace cap after use.
Work on internal parts should be carried out by a qualified technician. Removal of any covers is
considered a breach of warranty and will not be covered under any such agreement unless
authorized first by CHAUVET.
Troubleshooting
If you experience low output, or no output at all, unplug immediately. Check fluid level, the
external fuse, and main power supply. If all appear to be OK, plug the unit in again. If you are
unable to determine the cause of the problem, do not simply continue to use as this may damage
the unit. Contact CHAUVET for servicing.
Caution
• Do not obstruct the bubble wands. Never allow children to place fingers inside the front of
the machine. Do not leave machine unattended.
• Danger of Slipping. Bubble fluid produces a slippery residue. Do not leave machine
unattended.
• Always disconnect from main power supply before cleaning or servicing.
• Never use any other type of liquid other than quality bubble fluid. CHAUVET provide suitable
fluids for use with this machine (BJ-U or BJ-Q).
• Never drink bubble fluid. If its ingested, call a doctor immediately. If bubble fluid comes into
contact with eyes, rinse thoroughly with water.
• Beware of overfilling or spillage. Consider carefully when mounting.
• No user serviceable parts inside, please refer to CHAUVET for service.
Mounting Bracket
Bubble Wands
Fluid Tank Access
At the Rear:
fi Screw Cap
Fuseholder
fi Fan Blower
fi Mode Selector
Switch
fi Controller Socket
Fig.1