Filter
Top Products
F1
dynamic IP address from your
ISP, then select Obtain an IP
automatically as the WAN
Connection Type. If you also
select Use the Following DNS
Server Addresses, enter a spe-
cific DNS Server IP Address.
b Click the Save Settings button,
and go to Step G.
2Static IP
a If your ISP says that you are
connecting through a static or
fixed IP address from your ISP,
then select Static IP as the WAN
Connection Type.
b Enter the WAN IP Address, Sub-
net Mask Default Gateway
Address, and DNS Server pro-
vided by your ISP.
c In the DNS Server fields, enter
the DNS address(es) provided
by your ISP. You need to enter
at least one DNS address.
d Click the Save Settings button,
and go to Step G.
3 PPPoE
a If your ISP says that you are
connecting through PPPoE or if
you normally enter a user
name and password to access
tinue with the instruction,
below, to complete the Net-
work page.
D Depending on the setup infor-
mation from your ISP, you may
need to provide a host name
and domain name for the
Router. The Host Name and
Domain Name fields are usu-
ally left blank. If requested by
your ISP (usually cable ISPs),
complete these two fields.
E Choose the function of the
DMZ/Internet (WAN2) port. If the
port will be used as a second
Internet port, select Dual WAN.
If the port will be used as a
DMZ port, select DMZ.
F In the drop-down menus for
WAN1 and WAN2, the WAN
Connection Type setting fea-
tures four Internet connection
types: obtain an IP automati-
cally, Static IP, PPPoE, and PPTP.
Depending on which connec-
tion type you select, the fea-
tures available on the Network
page of the Setup screen will
differ. Proceed to the instruc-
tions for the connection type
you are using.
1 Obtain an IP Automatically
a If your ISP says that you are
connecting through DHCP or a
H Power your cable or DSL
modem off and back on
again.
I Restart or power on your PCs so
they can obtain the Router’s
new settings.
J To test the Router’s settings,
open your web browser from
any computer. In the browser’s
Address field, enter
www.linksys.com/registration
and press the Enter key.
Congratulations! The installation of
the Router is complete.
the Internet, then select PPPoE
as the WAN Connection Type.
b Enter the User Name and Pass-
word provided by your ISP.
c If you select Connect on
Demand, the PPPoE connec-
tion will be disconnected if it
has been idle for a period
longer than the Max Idle Time
setting.
d If you select Keep Alive, the
Router will keep the connec-
tion alive by sending out a few
data packets at the Redial
Period, so your Internet service
thinks that the connection is still
active.
e Click the Save Settings button.
f Go to Step G.
4PPTP
PPTP is a service used in Europe and
Israel only. IF you are using a PPTP
connection, check with your ISP for
the necessary setup information.
When you are finished, go to Step G.
G If you haven’t already done so,
click the Save Settings button.
Then, close the web browser.
RV082-QI-30924NC BW
For additional information or troubleshooting
help, refer to the User Guide on the Setup CD-
ROM. You can also call or e-mail for further
support.
24-hour Technical Support
800-326-7114
(toll-free from US or Canada)
E-mail Support
support@linksys.com
Website
http://www.linksys.com or
http://support.linksys.com
RMA (Return Merchandise Authorization)
http://www.linksys.com/support
FTP Site
ftp://ftp.linksys.com
Sales Information
800-546-5797 (800-LINKSYS)
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2003
Cisco Systems, Inc. All rights reserved.
Model No.
F2
F3
F4
J
D