Filter
Top Products
Ver.1.10
SCP-8550-LLV 2
< 2 / 2 >
Item Specification
RTC/CMOS data backed up by Lithium battery
The following table lists the Lithium battery specifications (button-type)
Specification CR2450
Voltage 3V
Capacity 620mAh
Weight 6.3g
RTC /CMOS
* The backup time of the CR2450 battery is over 7 years (In main
power is off, at 25
o
C).
* The clock is accurate to +/- 3 minutes/month at 25ºC.
Power Management
Power management setup via BIOS
Modem Ring On*6/Wake On LAN
Supports PC98/PC99 ACPI Power management
Bus
specification/Size(mm)
CompactPCI (6U double slot) / 160.0(L) x 233.4(H)
DC Power
Requirements
+5VDC±5%,
+12VDC±5% (for the heat sink fan),
+5VSB(Stand by) ±5% (Only when using the ATX power supply)
Power supply
specifications(Max.)
+5VDC 9A,
+12VDC 0.25A(for the heat sink fan)
+5VSB(Stand by) 0.5A (Only when using the ATX power supply)
(When using the Pentium M 1.6 GHz)
Operating
temperature/
Operating humidity
0 - 50°C /20 - 90%RH (No condensation)
Storage temperature -20 - 80°C
Floating dust particles Not to be excessive
Corrosive gases None
Weight 680g
Supported OS
Windows XP Professional
Windows XP Home Edition
Windows 2000 Professional
*1 Each connectors of this board front panel cannot be used simultaneously with J4, J5
connector.
*2 When using the J4 and J5 connector signal, optional rear panel I/O board (SCP-RPIO-01)
and the CPCI back plain boards corresponding to rear panel I/O are required.
*3 The IDE drives (include on board HDD and CF card) can connect the primary port and the
secondary port each maximum two drives. The primary port cannot be used by Ultra DMA
66/100 mode while using on board HDD. The secondary port cannot be used by Ultra
DMA 66/100 mode while using CF card.
*4 The DVI-D connector can connect only the digital (Panel-Link) input type display. The
analog RGB input type display is not connectable.
*5 Access LED blinks at the time of access to on board HDD and CF card. It does not blink
at the time of access to the drive connect to IDE signal of J4, J5 connectors.
(SCP-RPIO-01 has the access LED of the device that connected to the IDE port of J4, J5
connectors.)
*6 unsupported.
CPU
PCPM-16F Pentium M 1.6GHz (with heat sink-fan)
PCPMC-13F Celeron M 1.3GHz (with heat sink-fan)
Memory (PC2700 DDR SDRAM DIMM, No parity)
PC-MDD256-184A 184-Pin DDR-Memory (PC2700, 256MB)
PC-MDD512-184A 184-Pin DDR-Memory (PC2700, 512MB)
PC-MDD512-184A 184-Pin DDR-Memory (PC2700, 512MB)
OTHER
SCP-RPIO-01 Rear Panel I/O Board
CPU board [SCP-8550-LLV] …1
Product guide …1
IPC Precaution List …1
Driver disk utility *1 (CD-ROM) ...1
Jumper short pin (2mm) …2
Fixed bracket for on-board HDD …1
HDD fixed screws (M3 x 4) …4
*1 The CD-ROM contains the driver software and User’s Manual.
Daughter Board
Unused connector
RAS
connector
Printer port
connector
S1: CF master/
slave selector,
general-purpose SW
On-board
HDD connector
CF slot
43
44
S1
1
1
2
SER2
connector
Back side
CF slot
CPU Board
CN7
JP2: Clear CMOS
External
Battery
connector
DIMM1/2:
184 pin DDR RAM
connector
External ATX
power control
connector
FAN1
FAN2
SER1 connector
LAN1 connector
& USB 3/4 connector
VGA connector
DVI connector
Keyboard &
Mouse
Stack
Connector
J1
J2
J4
J5
LAN2 connector
& USB 1/2 connector
JP1: Clear CMOS
Option List
Packing List
Connector & Jumper Location