Filter
Top Products
loads uninterrupted.
◆Ethernet(RJ-45) Network Protection Ports
These ports are the protection for your computer network cable.
◆
Serial Port to PC
Professional Rack Mount Series UPS provides two
serial ports to allow connection and communication
between the UPS and two computers.
The two s
erial ports allow connection and
mary computer (with PowerPanel
®
Business Edition installed) is the computer that you will
:
art to
2. llowing the
BATTERY PACK REPLACEMENT AND STORAGE
AUTION!
communication from the DB-9 serial or USB port
on the computer to the UPS unit. These interfaces
are also compatible with the UPS service provided
by Windows 98, Windows ME, Windows 2000,
Windows NT, Windows XP, Windows Server
2003.
The Pri
use to control the UPS and make any change to the operation of the UPS. The Secondary
computer (with PowerPanel
®
installed) is unable to exhibit any control over the UPS.
When power failure occurs, one of the following shutdown sequences will be executed
1. If the Primary and Secondary serial ports are both in use: the Primary computer will st
count down (user controlled delay) for shutdown (User Control delay can be set in the
PowerPanel
®
Business Edition software. Recommended time is 5 minutes). Once the Primary
computer is shutdown, the UPS will signal the Secondary computer and initiate the Secondary
to shutdown. The UPS default shutdown time is 2 minutes. Therefore, it is recommended that
Secondary computer is set to shutdown within 1 minute in PowerPanel
®
Software.
If only the Secondary serial port is in use: the Secondary computer will shutdown fo
user settings in PowerPanel
®
Software. However, the Secondary computer will not able to
signal the UPS to shut down. Therefore, the UPS will only power off when it is in low battery.
C Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery
pack. Do not open the battery pack and service the batteries inside. If you have questions, contact
your dealer or call the number in this manual for information on battery replacement.
CAUTION! Use only CyberPower Battery Pack for replacement. See your dealer for this model.
CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a
fire, as it may explode. Follow all local ordinances regarding proper disposal of batteries.
CAUTION! Do not open or mutilate the batteries. Release electrolyte is harmful to the skin and eyes
ATTERY PACK REPLACEMENT PROCEDURE
and may be toxic.
B
er source.
UPS.
. Turn off and unplug all connected equipments.
1
2. Turn the UPS off and unplug it from the AC pow
3. Unplug the black and red wire of the Battery Pack from the
4. Follow the
Hard Installation Guide to connect a new Battery Pack to the UPS.
.
STORAGE
r UPS and disconnect its power cord from the wall outlet. Disconnect all cables
TROUBLE SHOOTING
irst turn off you
F
connected to the UPS to avoid battery drain. To store your UPS for an extended period, cover it and
store with the battery fully charged. Recharge the battery every three months to insure battery life. If
the battery remains uncharged for an extended period of time, it may suffer permanent loss of
capacity.
Problem Possible Cause Solution
Batter ed.
Recharge the batte the UPS plugged
ies are not fully charg
ry by leaving
in.
The ot
Battery is slightly worn out.
UPS does n
perform expected
runtime.
Contact CyberPower Systems at
service@cyberpower-eu.com
The on/off switch is designed to
nds and then turn
prevent damage by rapidly
turning it off and on.
Turn the UPS off. Wait 10 seco
the UPS on.
The unit is not connected to an e connected to a 220-240V
AC outlet.
The unit must b
50/60Hz outlet.
The battery is worn out.
r Systems at
Contact CyberPowe
service@cyberpower-eu.com
The UPS will not
Mechanical problem.
t
turn on.
Contact CyberPower Systems a
service@cyberpower-eu.com
Circuit breaker is tripped due to
ne piece of
overload.
Turn the UPS off and unplug at least o
equipment. Wait 10 seconds, reset the circuit
breaker and then turn the UPS on.
Batteries are discharged t 4 hours. Allow the unit to recharge for at leas
Outlets do not
o
y a
provide power t
equipment
Unit has been damaged b
surge or spike.
Contact CyberPower Systems at
service@cyberpower-eu.com
The serial/USB cable is not
the UPS unit and
connected.
Connect the serial/USB cable to
an open serial port on the back of the computer.
You must use the cable that came with the unit.
The serial/USB cable is
ort.
connected to the wrong p
Try another serial/USB port of your computer.
The unit is not providing battery
power.
Shut down your computer and turn the UPS off.
Wait 10 seconds and turn the UPS back on. This
should reset the unit.
PowerPanel
®
n or
al cable is not the cable e included with the unit for
Business Editio
PowerPanel
®
is
inactive (all icons
are gray).
The seri
that was provided with the unit.
You must use the cabl
the software.
Block Diagram
TECHNICAL SPECIFICATIONS
Model PR3000E
IN OUT
OUT
Capacity (VA) 3000VA
Capacity (Watts) 2200W
Input
Voltage Range 220-240Vac
Frequency Range 50/60 Hz
Output
On Battery Output Voltage Pure Sine Wave at 230Vac +/- 7%
On Battery Output Frequency 50/60 Hz
Transfer Time (Typical) 4ms
Overload Protection On Utility: Circuit Breaker, On ry: Internal Current Limiting Batte
Surge Protection and Filtering
Lightning / Surge Protection Yes
Network Protection RJ45(On ne Out) e In/O
Physical
Total # of UPS Receptacles 5 ( 3 IEC+ 2 Schuko)
Maximum Dimensions 2U Rack * 2
Weight (Kg) 55.5
Battery
Sealed Maintenance Free Lead
12V/7AHx8
Acid Battery
Typical Recharge Time 8 Hours
Warning Diagnostics
Indicators Power On, Using Battery, AVR, Load Level, Battery Level
Audible Alarms On Battery, Low Battery, Overload
Environmental
Operating Temperature + 32°F to 95°F (0°C to 35°C)
Operating Relative Humidity 0 to 95% NON-CONDENSING
Communication
PowerPanel
®
Business Edition Windows 98/ME/NT/2000/XP/Server 2003
Software
Management
Self-Test Manual Self-Test
Auto-Charger Yes
Auto-Restart Yes
USB Yes
SNMP / HTTP Network Optional
DEFINITIONS FOR ILLUMINATED LED INDICATORS
Power
On
AVR
Using
Circuit
Battery
Breaker
Alarm
Condition
On Off Off Set Off Normal
On Slow flash Off Set Off
AVR- Max. boost 13% o oltage for output
f input v
regulation while input voltage is from 8% to 15%
under nominal.
On Rapid flash Off Set Off
AVR- Max. boost 26% of input voltage for output
regulation while input voltage is from 15% to 26%
under nominal.
ON On Off Set Off
AVR- Max. buck 11% of input voltage for output
ver regulation while input voltage is from 8% to 26% o
nominal.
Off Off On Set Two Beeps
ilure- The UPS is providing battery power to
Utility Fa
the Battery-Power Supplied outlets.
Off Off On Set
Rapid
attery power.
Beeps
Utility Failure- The UPS is providing b
Rapid beeps indicate the battery will run out of charg
e
within a few minutes.
On/Off
On/ Off
On/Off Set Long Beep
Overload- Turn the UPS off and unplug at least one
/Flash
piece of equipment from the UPS. Wait 5 seconds,
reset the circuit breaker and restart the UPS.
Off Off On Up Long Beep
Overload- Turn the UPS off and unplug at least one
piece of equipment from the UPS. Wait 5 seconds,
reset the circuit breaker and restart the UPS.
Off Off Off Set Off
Surge Protection Malfunction- Power surge has
damaged the unit. Please contact CyberPower
Systems.
or more information, visit eu.cyberpowersystems.comF or contact
yberPower Systems, B.V. (Netherlands)
Netherlands
les@cyberpower-eu.com
C
Flight Forum 3545, 5657DW Eindhoven, The
Tel: + 31 73 649 1209, Fax : +31 (0)40 2340314 E-MAIL:
sa
yberPower Systems, Inc. (USA)
akopee, MN 55379, U.S.A.
rpowersystems.com
C
4241 12th Avenue East Suite 400 Sh
sales@cybe
Tel: +1 952 4039500, Fax: +1 952 4030009, E-MAIL:
ntire contents copyright ©2004 CyberPower Systems, B.V., All rights reserved. Reproduction in
yberPower warrants to you, the original purchaser, that CyberPower UPS will be free from defects
.
E
Input
AVR Switch
Battery
Charger
Transformer
Output
Battery
Inverter
(DC/AC)
® ®
and PowerPanel
whole or in part without permission is prohibited. PowerPanel
Plus are
trademarks of CyberPower Systems, (USA) Inc.
C
in design, assembly, materials and workmanship for two years ( battery is only one year) from the
date of original purchase. Any warranty services, please contact your local dealers or distributors