Filter
Top Products
CY7C1339G
Document #: 38-05520 Rev. *F Page 3 of 18
Pin Configurations (continued)
Pin Definitions
Name I/O Description
A
0
, A
1
, A Input-
Synchronous
Address Inputs used to select one of the 128K address locations. Sampled at the rising edge
of the CLK if ADSP
or ADSC is active LOW, and CE
1
,
CE
2
, and
CE
3
are sampled active. A1, A0
are fed to the two-bit counter.
.
BW
A
, BW
B
BW
C
, BW
D
Input-
Synchronous
Byte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to the SRAM.
Sampled on the rising edge of CLK.
GW
Input-
Synchronous
Global Write Enable Input, active LOW. When asserted LOW on the rising edge of CLK, a global
write is conducted (ALL bytes are written, regardless of the values on BW
[A:D]
and BWE).
BWE
Input-
Synchronous
Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal must be
asserted LOW to conduct a byte write.
CLK Input-
Clock
Clock Input. Used to capture all synchronous inputs to the device. Also used to increment the
burst counter when ADV
is asserted LOW, during a burst operation.
CE
1
Input-
Synchronous
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE
2
and CE
3
to select/deselect the device. ADSP is ignored if CE
1
is HIGH.
CE
1
is sampled only
when a new external address is loaded.
CE
2
Input-
Synchronous
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction with
CE
1
and CE
3
to select/deselect the device.CE
2
is sampled only when a new external address is
loaded.
CE
3
Input-
Synchronous
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE
1
and
CE
2
to select/deselect the device. CE
3
is sampled only when a new external address is
loaded. Not connected for BGA. Where referenced, CE
3
is assumed active throughout this
document for BGA.
OE
Input-
Asynchronous
Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins. When
LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as
input data pins. OE
is masked during the first clock of a read cycle when emerging from a
deselected state.
2345671
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
DDQ
NC/288M
NC/144M
NCDQ
C
DQ
D
DQ
C
DQ
D
AA AA
ADSP
V
DDQ
CE
2
A
DQ
C
V
DDQ
DQ
C
V
DDQ
V
DDQ
V
DDQ
DQ
D
DQ
D
NC
NC
V
DDQ
V
DD
CLK
V
DD
V
SS
V
SS
V
SS
V
SS
V
SS
V
SS
V
SS
V
SS
NC/576M
NC/1G
NC
NC
NCNCNCNC
NC/36MNC/72M
NC
V
DDQ
V
DDQ
V
DDQ
AAA
A
NC/9M
AA
A
AA
A
A0
A1
DQ
A
DQ
C
DQ
A
DQ
A
DQ
A
DQ
B
DQ
B
DQ
B
DQ
B
DQ
B
DQ
B
DQ
B
DQ
A
DQ
A
DQ
A
DQ
A
DQ
B
V
DD
DQ
C
DQ
C
DQ
C
V
DD
DQ
D
DQ
D
DQ
D
DQ
D
ADSC
NC
CE
1
OE
ADV
GW
V
SS
V
SS
V
SS
V
SS
V
SS
V
SS
V
SS
V
SS
NC
MODE
NC
NC
BW
B
BW
c
NC V
DD
NC
BW
A
NC
BWE
BW
D
ZZ
119-Ball BGA Pinout
[+] Feedback