Filter
Top Products
CY7C1386DV25, CY7C1386FV25
CY7C1387DV25, CY7C1387FV25
Document Number: 38-05548 Rev. *E Page 9 of 30
ZZ Mode Electrical Characteristics
Parameter Description Test Conditions Min. Max. Unit
I
DDZZ
Sleep mode standby current ZZ > V
DD
– 0.2V 80 mA
t
ZZS
Device operation to ZZ ZZ > V
DD
– 0.2V 2t
CYC
ns
t
ZZREC
ZZ recovery time ZZ < 0.2V 2t
CYC
ns
t
ZZI
ZZ Active to sleep current This parameter is sampled 2t
CYC
ns
t
RZZI
ZZ Inactive to exit sleep current This parameter is sampled 0 ns
Truth Table
[4, 5, 6, 7, 8, 9]
Operation Add. Used CE
1
CE
2
CE
3
ZZ ADSP ADSC ADV WRITE OE CLK DQ
Deselect Cycle, Power Down None H X X L X L X X X L-H Tri-State
Deselect Cycle, Power Down None L L X L L X X X X L-H Tri-State
Deselect Cycle, Power Down None L X H L L X X X X L-H Tri-State
Deselect Cycle, Power Down None L L X L H L X X X L-H Tri-State
Deselect Cycle, Power Down None L X H L H L X X X L-H Tri-State
Sleep Mode, Power Down None X X X H X X X X X X Tri-State
READ Cycle, Begin Burst External L H L L L X X X L L-H Q
READ Cycle, Begin Burst External L H L L L X X X H L-H Tri-State
WRITE Cycle, Begin Burst External L H L L H L X L X L-H D
READ Cycle, Begin Burst External L H L L H L X H L L-H Q
READ Cycle, Begin Burst External L H L L H L X H H L-H Tri-State
READ Cycle, Continue Burst Next X X X L H H L H L L-H Q
READ Cycle, Continue Burst Next X X X L H H L H H L-H Tri-State
READ Cycle, Continue Burst Next H X X L X H L H L L-H Q
READ Cycle, Continue Burst Next H X X L X H L H H L-H Tri-State
WRITE Cycle, Continue Burst Next X X X L H H L L X L-H D
WRITE Cycle, Continue Burst Next H X X L X H L L X L-H D
READ Cycle, Suspend Burst Current X X X L H H H H L L-H Q
READ Cycle, Suspend Burst Current X X X L H H H H H L-H Tri-State
READ Cycle, Suspend Burst Current H X X L X H H H L L-H Q
READ Cycle, Suspend Burst Current H X X L X H H H H L-H Tri-State
WRITE Cycle, Suspend Burst Current X X X L H H H L X L-H D
WRITE Cycle, Suspend Burst Current H X X L X H H L X L-H D
Notes
4. X = Don't Care, H = Logic HIGH, L = Logic LOW.
5. WRITE
= L when any one or more byte write enable signals and BWE = L or GW = L. WRITE = H when all byte write enable signals, BWE, GW = H.
6. The DQ pins are controlled by the current cycle and the
OE
signal.
OE
is asynchronous and is not sampled with the clock.
7. CE
1
, CE
2
, and CE
3
are available only in the TQFP package. BGA package has only 2 chip selects CE
1
and CE
2
.
8. The SRAM always initiates a read cycle when ADSP
is asserted, regardless of the state of GW, BWE, or BW
X
. Writes may occur only on subsequent clocks after
the ADSP
or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a don't
care for the remainder of the write cycle.
9. OE
is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are tri-state when OE is
inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).
[+] Feedback