Filter
Top Products
CY7C1511V18, CY7C1526V18
CY7C1513V18, CY7C1515V18
Document Number: 38-05363 Rev. *F Page 21 of 32
Maximum Ratings
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with Power Applied.. –55°C to +125°C
Supply Voltage on V
DD
Relative to GND........–0.5V to +2.9V
Supply Voltage on V
DDQ
Relative to GND.......–0.5V to +V
DD
DC Applied to Outputs in High-Z ........ –0.5V to V
DDQ
+ 0.3V
DC Input Voltage
[13]
.............................. –0.5V to V
DD
+ 0.3V
Current into Outputs (LOW) ........................................ 20 mA
Static Discharge Voltage (MIL-STD-883, M. 3015).. > 2001V
Latch-up Current ................................................... > 200 mA
Operating Range
Range
Ambient
Temperature (T
A
) V
DD
[17]
V
DDQ
[17]
Commercial 0°C to +70°C 1.8 ± 0.1V 1.4V to
V
DD
Industrial –40°C to +85°C
Electrical Characteristics
DC Electrical Characteristics
Over the Operating Range
[14]
Parameter Description Test Conditions Min Typ Max Unit
V
DD
Power Supply Voltage 1.7 1.8 1.9 V
V
DDQ
IO Supply Voltage 1.4 1.5 V
DD
V
V
OH
Output HIGH Voltage Note 18 V
DDQ
/2 – 0.12 V
DDQ
/2 + 0.12 V
V
OL
Output LOW Voltage Note 19 V
DDQ
/2 – 0.12 V
DDQ
/2 + 0.12 V
V
OH(LOW)
Output HIGH Voltage I
OH
= −0.1 mA, Nominal Impedance V
DDQ
– 0.2 V
DDQ
V
V
OL(LOW)
Output LOW Voltage I
OL
= 0.1 mA, Nominal Impedance V
SS
0.2 V
V
IH
Input HIGH Voltage V
REF
+ 0.1 V
DDQ
+ 0.3 V
V
IL
Input LOW Voltage –0.3 V
REF
– 0.1 V
I
X
Input Leakage Current GND ≤ V
I
≤ V
DDQ
−5 5 μA
I
OZ
Output Leakage Current GND ≤ V
I
≤ V
DDQ,
Output Disabled −5 5 μA
V
REF
Input Reference Voltage
[20]
Typical Value = 0.75V 0.68 0.75 0.95 V
I
DD
[21]
V
DD
Operating Supply V
DD
= Max,
I
OUT
= 0 mA,
f = f
MAX
= 1/t
CYC
300MHz (x8) 930 mA
(x9) 940
(x18) 1020
(x36) 1230
278MHz (x8) 865 mA
(x9) 870
(x18) 950
(x36) 1140
250MHz (x8) 790 mA
(x9) 795
(x18) 865
(x36) 1040
Notes
17. Power up: Assumes a linear ramp from 0V to V
DD
(min) within 200 ms. During this time V
IH
< V
DD
and V
DDQ
< V
DD
.
18. Output are impedance controlled. I
OH
= −(V
DDQ
/2)/(RQ/5) for values of 175 ohms <= RQ <= 350 ohms.
19. Output are impedance controlled. I
OL
= (V
DDQ
/2)/(RQ/5) for values of 175 ohms <= RQ <= 350 ohms.
20. V
REF
(min) = 0.68V or 0.46V
DDQ
, whichever is larger, V
REF
(max) = 0.95V or 0.54V
DDQ
, whichever is smaller.
21. The operation current is calculated with 50% read cycle and 50% write cycle.
[+] Feedback