Filter
Top Products
CY7C1566V18, CY7C1577V18
CY7C1568V18, CY7C1570V18
Document Number: 001-06551 Rev. *E Page 10 of 28
Truth Table
The truth table for CY7C1566V18, CY7C1577V18, CY7C1568V18, and CY7C1570V18 follows.
[3, 4, 5, 6, 7, 8]
Operation K LD R/W DQ DQ
Write Cycle:
Load address; wait one cycle;
input write data on consecutive K and K
rising edges.
L-H L L D(A) at K(t + 1) ↑ D(A+1) at K
(t + 1) ↑
Read Cycle: (2.5 cycle Latency)
Load address; wait two and half cycle;
read data on consecutive K and K
rising edges.
L-H L H Q(A) at K(t + 2) ↑ Q(A+1) at K(t + 3) ↑
NOP: No Operation L-H H X High Z High Z
Standby: Clock Stopped Stopped X X Previous State Previous State
Write Cycle Descriptions
The write cycle description table for CY7C1566V18 and CY7C1568V18 follows.
[3, 9]
BWS
0
/
NWS
0
BWS
1
/
NWS
1
K
K
Comments
L L L–H – During the data portion of a write sequence:
CY7C1566V18 − both nibbles (D
[7:0]
) are written into the device.
CY7C1568V18 − both bytes (D
[17:0]
) are written into the device.
L L – L-H During the data portion of a write sequence:
CY7C1566V18 − both nibbles (D
[7:0]
) are written into the device.
CY7C1568V18 − both bytes (D
[17:0]
) are written into the device.
L H L–H – During the data portion of a write sequence:
CY7C1566V18 − only the lower nibble (D
[3:0]
) is written into the device, D
[7:4]
remains unaltered.
CY7C1568V18 − only the lower byte (D
[8:0]
) is written into the device, D
[17:9]
remains unaltered.
L H – L–H During the data portion of a write sequence:
CY7C1566V18 − only the lower nibble (D
[3:0]
) is written into the device, D
[7:4]
remains unaltered.
CY7C1568V18 − only the lower byte (D
[8:0]
) is written into the device, D
[17:9]
remains unaltered.
H L L–H – During the data portion of a write sequence:
CY7C1566V18 − only the upper nibble (D
[7:4]
) is written into the device, D
[3:0]
remains unaltered.
CY7C1568V18 − only the upper byte (D
[17:9]
) is written into the device, D
[8:0]
remains unaltered.
H L – L–H During the data portion of a write sequence:
CY7C1566V18 − only the upper nibble (D
[7:4]
) is written into the device, D
[3:0]
remains unaltered.
CY7C1568V18 − only the upper byte (D
[17:9]
) is written into the device, D
[8:0]
remains unaltered.
H H L–H – No data is written into the devices during this portion of a write operation.
H H – L–H No data is written into the devices during this portion of a write operation.
Notes
3. X = “Don’t Care,” H = Logic HIGH, L = Logic LOW, ↑
represents rising edge.
4. Device powers up deselected with the outputs in a tri-state condition.
5. “A” represents address location latched by the devices when transaction was initiated. A + 1 represents the address sequence in the burst.
6. “t” represents the cycle at which a read/write operation is started. t + 1 and t + 2 are the first and second clock cycles succeeding the “t” clock cycle.
7. Data inputs are registered at K and K
rising edges. Data outputs are delivered on K and K rising edges.
8. Cypress recommends that K = K
= HIGH when clock is stopped. This is not essential but permits most rapid restart by overcoming transmission line charging
symmetrically.
9. Is based on a write cycle is initiated per the Write Cycle Descriptions table. NWS
0
, NWS
1
,
BWS
0
, BWS
1
, BWS
2
,
and BWS
3
are altered on different portions of a write
cycle, as long as the setup and hold requirements are met.
[+] Feedback [+] Feedback