Filter
Top Products
board extractors engage the guide holes in the
chassis card cage, then lock down the board
extractors until the red locking tabs snap shut.
CAUTION: CompactPCI backplane pins are bent
easily. Make sure that the board is seated with hand
pressure before fully seating board. If board extractors
are used to seat the board, make sure to seat evenly.
NOTE: If the power to the chassis is on, power is
automatically applied to the board, the Out of Service LED
lights briefly and then goes out, and the Power LED goes
on.
5. Tighten the retaining screws to secure the board
firmly in the chassis slot (optional).
6. If the power to the chassis is turned OFF, turn the
power to the chassis ON.
Connecting External Cables
For information about the pinouts for the network interface
cable, refer to the Pinouts for the RJ-48C figure.
Pinouts for the RJ-48C
RJ-48C Network Interface
Cable Connector
CHASSIS GROUND
CHASSIS GROUND
UNUSED
XMIT_TIP
XMIT_RING
UNUSED
RCV_TIP
RVC_RING
8
7
6
5
4
3
2
1
8
7
6
5
4
3
2
1
Pinouts for the RJ–48C
Jack on Bracket
Pin 1
After Installing the Hardware
After installing the hardware, proceed with the Dialogic
®
System Software installation as described in the system
software documentation (if applicable).
For technical specifications and product information, see
the Dialogic website at
http://www.dialogic.com/products.htm
Removing the Main Board
Exercise caution when removing the board from a
CompactPCI chassis. The board extractors are equipped
with red locking tabs that lock when the board is correctly
positioned in the chassis.
To remove the board from the chassis, simultaneously
press down both red locking tabs (see the CompactPCI
Extractor figure) on the extractors before applying
pressure away from the center of the board to disengage.
CAUTION: When removing the board, if the red locking
tabs on the extractors are not pressed while applying
pressure to the extractors, there is a risk of breaking the
tabs.
CompactPCI Extractor
Press and hold down the red
locking tabs on both board
extractors before applying
pressure to the board.
Removing the Rear I/O Module
NOTE: In a live insertion (powered-on) system, do not
remove and replace a Rear I/O module while the main
(front) board is in service. Remove the front board first,
then remove and replace the Rear I/O module, and then
reinsert the front board.
To remove the board from the chassis, simultaneously
press down both red locking tabs (see the CompactPCI
Extractor figure) on the extractors before applying
pressure away from the center of the board to disengage.
Warranty and Return Information
Warranty Period
For specific warranty information for this board, refer to the
Warranty section of the Products page, located at this
URL: http://www.dialogic.com/warranties/.
Contacting Technical Support
Dialogic provides technical support for its products through
a network of value added distributors who are trained to
answer technical questions on installing and configuring
Dialogic
®
products. If you are unsure how to contact your
support channel, please call Dialogic in the United States
at 973-967-6600 (9am-5pm EST) and we will assist in
obtaining the appropriate support channel.
Outside the United States please refer to
http://www.dialogic.com/support/contact to obtain
local contact information. Dialogic also provides direct
support via Dialogic
®
Pro™ Services agreements. For
more details of direct support from Dialogic please refer to:
http://www.dialogic.com/support/DialogicPro.
Returning a Product
To return a board for warranty repair or any other returns,
please refer to the following:
http://www.dialogic.com/support/hwfaults.
Sales Assistance
If you have a sales question, please contact your
local Sales Representative or the Regional Sales Office for
your area. Address, telephone and fax numbers, are
available at the Dialogic website located at:
http://www.dialogic.com/contact.htm.
To purchase Dialogic
®
products, please refer to the
following website to locate the appropriate supplier:
http://www.dialogic.com/purchase.htm.
All contents of this document are furnished for informational use only and are subject to change
without notice and do not represent a commitment on the part of Dialogic Corporation or its
subsidiaries (“Dialogic”). Reasonable effort is made to ensure the accuracy of the information
contained in the document. However, Dialogic does not warrant the accuracy of this information
and cannot accept responsibility for errors, inaccuracies or omissions that may be contained in
this document.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH
DIALOGIC
®
PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR
OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU
AND DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC
DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR
USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING
TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR
INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.
Dialogic products are not intended for use in medical, life saving, life sustaining, critical control
or safety systems, or in nuclear facility applications.
It is possible that the use or implementation of any one of the concepts, applications, or ideas
described in this document, in marketing collateral produced by or on web pages maintained by
Dialogic may infringe one or more patents or other intellectual property rights owned by third
parties. Dialogic does not provide any intellectual property licenses with the sale of Dialogic
products other than a license to use such product in accordance with intellectual property owned
or validly licensed by Dialogic and no such licenses are provided except pursuant to a signed
agreement with Dialogic. More detailed information about such intellectual property is available
from Dialogic’s legal department at 9800 Cavendish Blvd., 5
th
Floor, Montreal, Quebec, Canada
H4M 2V9. Dialogic encourages all users of its products to procure all necessary intellectual
property licenses required to implement any concepts or applications and does not condone
or encourage any intellectual property infringement and disclaims any responsibility
related thereto. These intellectual property licenses may differ from country to country and
it is the responsibility of those who develop the concepts or applications to be aware of and
comply with different national license requirements.
Dialogic, Diva, Eicon, Eicon Networks, Eiconcard, Dialogic Pro and SIPcontrol, among others,
are either registered trademarks or trademarks of Dialogic. Dialogic's trademarks may be used
publicly only with permission from Dialogic. Such permission may only be granted by Dialogic’s
legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any
authorized use of Dialogic's trademarks will be subject to full respect of the trademark guidelines
published by Dialogic from time to time and any use of Dialogic’s trademarks requires proper
acknowledgement. The names of actual companies and products mentioned herein are the
trademarks of their respective owners.