Filter
Top Products
5. Tighten the retaining screws to secure the board
firmly in the chassis slot.
6. Connect the Rear I/O module to the rear of the slot
selected in Step 3.
CAUTION: Damage to the board will result if an
incorrect rear I/O module is used. Use a Rear I/O
module only and be careful to install the module in the
correct slot.
Use the slot’s board guides as you insert the board
into the chassis slot. Make sure that the tabs on the
board extractors engage the guide holes in the
chassis card cage, then lock down the board
extractors until the red locking tabs snap shut.
CAUTION: cPCI backplane pins are bent easily. Make
sure that the board is seated with hand pressure before
fully seating board. If the board extractors are used to
seat the board, make sure to seat evenly.
7. Tighten the retaining screws to secure the board
firmly in the chassis slot.
8. Select a new slot and repeat steps 4-7 for each board
you are installing.
9. If the power to the chassis was turned OFF in step 1,
turn the power to the chassis ON.
Connecting External Cables
Connect either the 100BASE-TX or 1000BASE-T
Ethernet cables to the appropriate Rear I/O module
connectors. When connecting the Ethernet cables, install
a snap-fit ferrite clamp on each cable as close as
possible to the connector on the Rear I/O module.
Diameter
5m m (approx.)
Ethernet Cable
Ferrite Clamp
CAUTION: A ferrite clamp must be installed on all
cables that connect to Ethernet connectors to meet
EMC requirements. Two ferrite clamps have been
provided, therefore only two cables can be connected at
one time.
100BASE-TX Ethernet Connector Pinouts
100BT 0
Pin 1
Link
Established
Indicator
(G reen)
Activity
Indicator
(Yellow)
Pin
1
2
3
4
5
6
7
8
Label
RD+
RD-
TD+
NC
NC
TD-
NC
NC
1000BASE-T Ethernet Connector Pinouts
1000BT 0
Link
Established
Indicator
(Green)
Link Not
Established
Indicator
(Yellow)
Pin 1
Pin
1
2
3
4
5
6
7
8
Label
TP 0+
TP 0-
TP 1+
TP 2+
TP 2-
TP 1-
TP 3+
TP 3-
After Installing Hardware
After installing the hardware, run the Dialogic
®
Configuration Manager (DCM) as described in the
installation instructions included with the Dialogic
®
System Software to configure your system. For technical
specifications and product information go to:
http://www.dialogic.com/products.htm.
Uninstalling the Hardware
Removing the Main Board
Exercise caution when removing the board from a cPCI
chassis. The board extractors are equipped with red
locking tabs that lock when the board is correctly
positioned in the chassis.
CAUTION: When removing the board, if the red locking
tabs on the extractors are not pressed while applying
pressure to the extractors, there is a risk of breaking.
To remove the board from the chassis, simultaneously
press down both red locking tabs (see the figure below)
on the extractors before applying pressure away from the
center of the board to release the board from the
chassis.
Press and hold down
the red locking tabs on
both board extractors
before applying
pressure to the board
extractors
Removing the Rear I/O Module
In a live insertion (powered-on) system, do not remove
and replace a Rear I/O module while the main (front)
board is in service. Remove the front board first, then
remove and replace the Rear I/O module, and then
reinsert the front board. Remove the Rear I/O module
using the red locking tabs as described above.
Warranty and Return Information
For specific warranty information for this board, refer to
the Warranty section of the Products page, located at
this URL: http://www.dialogic.com/warranties/.
Contacting Technical Support
Dialogic provides technical support for its products
through a network of value added distributors who are
trained to answer technical questions on installing and
configuring Dialogic
®
products. If you are unsure how to
contact your support channel, please call Dialogic in the
United States at 973-967-6600 (9am-5pm EST) and we
will assist in obtaining the appropriate support channel.
Outside the United States please refer to
http://www.dialogic.com/support/contact to obtain
local contact information. Dialogic also provides direct
support via Dialogic
®
Pro™ Services agreements. For
more details of direct support from Dialogic please refer
to: http://www.dialogic.com/support/DialogicPro.
Returning a Product
To return a board for warranty repair or any other
returns, please refer to the following:
http://www.dialogic.com/support/hwfaults.
Sales Assistance
If you have a sales question, please contact your
local Sales Representative or the Regional Sales Office
for your area. Address, telephone and fax numbers, are
available at the Dialogic website located at:
http://www.dialogic.com/contact.htm. To purchase
Dialogic
®
products, please refer to the following website
to locate the appropriate supplier:
http://www.dialogic.com/purchase.htm.
All contents of this document are furnished for informational use only and are subject to change without notice and do not
represent a commitment on the part of Dialogic Corporation or its subsidiaries (“Dialogic”). Reasonable effort is made to
ensure the accuracy of the information contained in the document. However, Dialogic does not warrant the accuracy of this
information and cannot accept responsibility for errors, inaccuracies or omissions that may be contained in this document.
®
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH DIALOGIC
PRODUCTS. NO
LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS
IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN A SIGNED AGREEMENT BETWEEN YOU AND
DIALOGIC, DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC DISCLAIMS ANY EXPRESS
OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY
OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR
INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.
Dialogic products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in
nuclear facility applications.
It is possible that the use or implementation of any one of the concepts, applications, or ideas described in this document, in
marketing collateral produced by or on web pages maintained by Dialogic may infringe one or more patents or other
intellectual property rights owned by third parties. Dialogic does not provide any intellectual property licenses with the sale of
Dialogic products other than a license to use such product in accordance with intellectual property owned or validly licensed
by Dialogic and no such licenses are provided except pursuant to a signed agreement with Dialogic. More detailed
information about such intellectual property is available from Dialogic’s legal department at 9800 Cavendish Blvd., 5
th
Floor,
Montreal, Quebec, Canada H4M 2V9. Dialogic encourages all users of its products to procure all necessary intellectual
property licenses required to implement any concepts or applications and does not condone or encourage any
intellectual property infringement and disclaims any responsibility related thereto. These intellectual property licenses
may differ from country to country and it is the responsibility of those who develop the concepts or applications to be
aware of and comply with different national license requirements.
Dialogic, Diva, Eicon, Eicon Networks, Eiconcard and SIPcontrol, among others, are either registered trademarks or
trademarks of Dialogic. Dialogic's trademarks may be used publicly only with permission from Dialogic. Such permission
may only be granted by Dialogic’s legal department at 9800 Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M
2V9. Any authorized use of Dialogic's trademarks will be subject to full respect of the trademark guidelines published by
Dialogic from time to time and any use of Dialogic’s trademarks requires proper acknowledgement. The names of actual
companies and products mentioned herein are the trademarks of their respective owners.