Filter
Top Products
DYMO 1000
DYMO 1000
Introduction
The Dymo 1000 Electronic Labelmaker enables you to create a
wide variety of high quality self-adhesive labels of up to 100
characters.
The Labelmaker uses 12mm (
1
/
2
wide tape cassettes in a
number of label colours.
Normal or double width, full and half-height text can be printed
in a single line, or in half-height on two lines.
Text can be set horizontally or and is
always centred on the label.
ON/OFF
Switches the power on and off.
• Switches off automatically after
three minutes if no keys are
pressed. The last label created
will be stored and displayed
when next turned on.
Note: If the batteries are removed
for more than a few seconds, or the
external power supply interrupted,
all text and settings will be lost.
When power is restored, the
display will show a flashing cursor
(no text) and the settings will be full-
height, normal width, auto length,
and
CAPS
off.
CAPITALS
CAPS
• Press for all subsequent
characters in UPPER CASE
(CAPITALS), as confirmed by
the indicator in the top left
corner of the display.
• Press again to cancel and
return to lower case.
SHIFT KEY
• Press and release before
pressing an alphabet key to
produce an UPPER CASE
character, as confirmed by the
indicator in the lower left corner
of the display.
• For dual purpose keys, press
first to produce the legend
above the key.
• Pressing
while
CAPS
is set,
will give lower case characters.
DELETE
DEL
• Press to delete the character to
the left of the cursor, or to
cancel certain function key
operations.
Function keys
v
e
r
t
i
c
a
l
l
y
This label has
two line text.
TEXT SIZE
SIZE
• Press to display the symbols
representing the four text print
sizes:
normal height and width
normal height, double width
half-height, normal width
half-height, double width.
The cursor will be positioned
over the current selection.
• Press
DEL
to cancel, or use
<
or
<
to move the cursor
over the size symbol required,
then press
SIZE
to confirm the
selection, or
PRINT
1
,
2
,
3
.
.
.
n
to fix the new
size and print the label.
TWO-LINE TEXT +
2-LINE
CAPS
Labels comprising two lines of
text can be printed on the 12mm
(
1
/
2
") wide labels.
• Press to insert the special
character
at the point where
you want the text to break, eg:
This label has two line text.
on the display will print as:
Only one
can be included in
a label at a time.
• Press
DEL
to delete , as for
normal text characters.
Note: Two lines cannot be printed
vertically.
VERTICAL TEXT +
VERT
SYM
• Rotates the text through 90°
so that the label is printed
, as
confirmed by the indicator in the
top right of the display.
• Press again to cancel and
return to horizontal text.
CLEAR TEXT +
CLEAR
DEL
• Press to clear all the text and
the length setting, but leave the
print size and style settings
unchanged.
CURSOR KEYS
<
<
These keys move the cursor
along the text.
• Pressing
+
<<
<
or +
<<
<
moves the cursor to the
beginning or end of the text.
When used in conjunction with
certain function keys, use
<
or
<
to select options and
numerical values.
• To insert characters into the text,
use
<
or
<
to position the
cursor under the character to the
right of the insertion point, then
type in the characters required.
PRINTING
PRINT
1
,
2
,
3
.
.
.
n
• Press
PRINT
1
,
2
,
3
.
.
.
n
to print the label.
• Press the cutter button to
release the label.
SPACE KEY
• Press to insert a
space into the text.
FEED +
FEED
• Press to feed out 25mm of tape
without printing.
SYMBOLS
SYM
• Press to select a symbol
character – see ‘Symbols and
special characters’.
v
e
r
t
i
c
a
l
l
y
4
Creating your first label
• Fit batteries or connect the AC adaptor, and
insert a tape cassette.
• Press
to switch on.
• Type in your text using the alphabet keys; each
character will appear in the display. If you make a
mistake, press
DEL
to delete the error, then type
in the correction.
• Press
PRINT
1
,
2
,
3
.
.
.
n
to print the label, then press the cutter
button to release the label.
The Display
12345
—
The display shows:
• Up to five text characters, plus the cursor, at one
time. Use
<
or
<
to move along the text.
• Four indicators, one in each corner – as shown
above.
• The display will flash if you press an incorrect key in
a function sequence.
Vertical textCAPS lock on
Shift on
Fixed length on
CURSOR
Label cutter
button. Press to
release label.
NOTE:
Always remove
a cut label
before printing
another.
1
2
3
4
+
6
7
8
9
0
5
=
£
$
’
-
%
/
:
*
(
)
’
.
SIZE
LENGTH
VERT
CLEAR2-LINE
CAPS
SYM
DEL
PRINT
AB
C
DF
E
G
H
I
JKL
MN
O
P
Q
R
STUVW
X
YZ
FEED
!
i
?
?
N
~
C
,
^
/
/
..
<<
<
<<
<
Œ
1
,
2
,
3
.
.
.
n
LABEL LENGTH +
SIZE
LENGTH
Displays the current label length.
The length is normally calculated
automatically, according to the
length of the text on the label.
• Press
DEL
to cancel the length
function without changing the
length, or:
• use
<
or
<
to increase (up to
400mm or 15" max.) or
decrease the length in 5mm
(
1
/
5
") steps. The display will
flash if you try to make the label
shorter than the text.
• If the length displayed is
preceded by the > symbol, the
length has already been fixed;
the label is too short for the text
and it will not print. Either press
<
to increase the length in
5mm (
1
/
5
") steps until the >
symbol disappears, or press
+
CLEAR
DEL
to cancel fixed
length; the label is now long
enough for the text and can be
printed.
• Press
+
SIZE
LENGTH
again to fix
the length for all subsequent
labels as indicated in the lower
right corner of the display, or
• press
PRINT
1
,
2
,
3
.
.
.
n
to fix the new
length and print the label.
• Pressing
+
CLEAR
DEL
will cancel
the fixed length and restore the
automatic length.
INCREMENTAL
PRINTING
+
PRINT
1
,
2
,
3
.
.
.
n
Prints a label then increments the
last digit of any number in the
label by 1, ready for the next print
command.
• Press
PRINT
1
,
2
,
3
.
.
.
n
to print the next
label, or
+
PRINT
1
,
2
,
3
.
.
.
n
to print the
next label and increment again
by 1.
5