Extron electronic IN1608 Switch User Manual


  Open as PDF
of 4
 
4
68-1916-50 Rev. A
06 13
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
Firmware Upgrades
The rmware of the scaler can be upgraded via the internal web pages or the Extron Firmware Loader program (available on the Extron website,
www.extron.com). The internal web pages cannot be accessed through the USB port.
Basic SIS Command Table
IN1608 scalers can be congured with specic SIS commands via an RS-232, USB, or Ethernet connection. Use the Extron DataViewer utility
or a control system to send and receive SIS commands. The table below lists a selection of SIS commands. For a full list of SIS commands and
variables, see the IN1608 User Guide at www.extron.com.
Command ASCII Command
(Host to Device)
Response
(Device to Host)
Additional Description
Select audio and video input
X!! InX!
•
All] Selects audio and video input X!.
Select video input only
X!& InX!
•
RGB] Selects the video only input X!.
Select audio input only
X!$ InX!
•
Aud] Selects the audio only input X!.
Execute Auto-Image
A
Img0
]
Executes an Auto-Image on the current input.
Execute Auto-Image and ll
1*A
Img1
]
Executes an Auto-Image and lls the output.
Execute Auto-Image and follow
2*A
Img2
]
Executes an Auto-Image and maintains the aspect ratio
of the current input.
Mute video to black
1B
Vmt1
]
Mutes the video and displays a black output.
Mute video and sync
2B
Vmt2
]
Mutes the video and sync output.
Unmute video and sync
0B
Vmt0
]
Unmutes the video.
NOTE: By default, adjusting variable volume with the following commands only affects variable analog output (configurable through group
masters).
Set variable volume level
ED8*X4$GRPM} GrpmD08*X4$]
Set the variable volume to a value of X4$.
Raise variable volume
ED8*X4*+GRPM}
GrpmD08*X4$]
Increase the level of the variable volume by X4* dB.
Lower variable volume
ED8*X4*-GRPM}
GrpmD08*X4$]
Decrease the level of the variable volume by X4* dB.
View variable volume level
ED8GRPM} X4$]
View the current variable volume level.
NOTE: By default, setting the audio mute with the following commands affects all outputs (configurable through group masters).
Set master audio mute
ED7*X(GRPM} GrpmD07*X(]
Enable or disable master audio mute.
View master audio mute status
ED7GRPM} X(]
View the current master audio mute status.
Enable executive mode 1
1X
Exe1
]
Locks the entire front panel.
Enable executive mode 2
2X
Exe2
]
Locks the front panel except for input selection and
volume control.
Disable executive modes
0X
Exe0
]
Allows all front panel adjustments and selections.
Set scaler IP address
EX4)CI} Ipi
•
X4)]
Species a new scaler IP address.
Set scaler DHCP mode
EX(DH} IdhX(]
Enables or disables DHCP (0 = default).
Set subnet mask
EX4!CS} Ips
•
X4!]
Species a new subnet mask.
Set gateway IP address
EX4@CG} Ipg
•
X4@]
Species a new gateway IP address.
Reboot networking
E2BOOT} Boot2]
Restarts the network connection after IP or DHCP
changes.
NOTE: IP settings will not take effect until the E2BOOT} command is executed.
NOTES:
X! = Input selection (1-8)
X( = Enable or disable (0 = off or disabled; 1 = on or enabled)
X4) = IP address (xxx.xxx.xxx.xxx; 192.168.254.254 = default)
X4! = Subnet mask (xxx.xxx.xxx.xxx; 255.255.0.0 = default)
X4@ = Gateway address (xxx.xxx.xxx.xxx; 0.0.0.0 = default)
X4$ = Group volume level (-1000 to 0, where -1000 = -100 dB or 0% volume and 0 = 0 dB or 100% volume)
X4* = Increment value (dB value multiplied by ten, in 0.1 dB increments, to raise or lower a group fader [for example, 100 = 10 dB])
 previous