Filter
Top Products
Sensor lights up
Touch test area
Press Auto-On ( )
GLISH
E
EN
EN
EN
ENG
ENG
ENG
ENGL
ENGL
ENGL
ENGLI
ENGLIS
ENGLIS
ENGLIS
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
ENGLISH
Model HD-10Cs
Model HD-10C
2
— To Test SafeSense
™
Technology
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
CAPABILITIES
Breakthrough Safety Technology! SafeSense™ stops shredding when hands are too close to the opening.
• Keep away from children and pets. Keep hands away from paper
entry. Always unplug when not in use.
• Keep foreign objects – gloves, jewelry, clothing, hair, etc.– away
from shredder openings. If object enters top opening, press and
hold Reverse (R) to back out object.
• Never use aerosol, petroleum-based or other flammable products on or
near shredder. Do not use canned air on shredder.
• Do not use if damaged or defective. Do not open shredder head.
Do not place near or over heat or water source.
• 10 sheets per pass to avoid jams.
• Avoid touching exposed blades under Confetti-Cut shredder head.
• The socket-outlet shall be installed near the equipment and shall be easily
accessible.
Will shred:
Paper, small paper clips, credit cards and staples
Will not shred:
Continuous forms, adhesive labels, transparencies, newspaper,
cardboard, large paper clips, laminates or plastic other than
noted above
Paper shred size:
Confetti-Cut
.....................................................................
5/32” x 2” (3.9 x 50mm)
Maximum:
Sheets per pass (Confetti-Cut)
.............................................................................
10*
Cards per pass
.......................................................................................................
1
Passes per day
...............................................................................................
10-20
Paper width
............................................................................................
9”/229mm
Continuous operation
.............................................................................
4-5 minutes
*20 lb., 8.5”x11” paper at 120v, 60 Hz,
3.8
Amps; heavier paper, humidity or other
than rated voltage may reduce capacity.
SET-UP
Place head on basket
as shown:
10
Overheated (red)
Control switch
Safe Sense™ Technology (yellow)
Standby (green)
Shredder head
Paper entry
Auto-On ( )
Off
Reverse (R)
Mesh basket
Grips
Bin full indicator
Safe Sense™ override switch
See safety instructions below
Handle
Set to Off
Feed into paper entry
and release
Set to Off
LIMITED WARRANTY Fellowes, Inc. (“Fellowes”) warrants the cutting blades of the machine to be free from
defects in material and workmanship for 3 years from the date of purchase by the original consumer.
Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 1
year from the date of purchase by the original consumer. If any part is found to be defective during the
warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and
expense, of the defective part.
This warranty does not apply in cases of abuse, mishandling, or unauthorized repair. ANY IMPLIED
WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY
LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall
Fellowes be liable for any consequential or incidental damages attributable to this product.
This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid
worldwide, except where different limitations, restrictions, or conditions may be required by local law.
For more details or to obtain service under this warranty, please contact us or your dealer.
Gently pull uncut paper
from paper entry. Plug in.
Press and hold
Reverse (R)
2-3 seconds
Set to Off (O)
and unplug
Run regularly in reverse for
one minute
Oil when bin is full, or
immediately, if:
• Capacity decreases
• Motor sounds different, or
Shredder stops running
OPERATION
TROUBLESHOOTING
MAINTENANCE
3
Shredder doesn’t start:
Follow oiling procedure below and repeat twice.
WARRANTY
Alternate slowly back and forth
*Apply oil
across entry
Press and hold
Reverse (R)
2-3 seconds
Shred one sheet
Set to Off
Press Auto-On ( )
Yellow - SafeSense™ active
Yellow flashing - SafeSense™ not active
Make sure head is on basket correctly
Wait 20 minutes for motor to cool down
Remove and empty basket
Press Auto-On ( )
Paper jam:
Set to Off (O), remove shredder head and empty bin. Replace shredder head, and follow any or all of the
below procedures.
PAPER
CARD
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
/3505006
0
ATTENTION:
If the SafeSense™ light remains on, you must engage the
Override Switch
in order to perform steps above. Once the jam is cleared, reset the
SafeSense™ feature. (See SafeSense™ instructions below.)
SafeSense™ override switch
Active
Not active
Sensor light illuminated–paper
jammed
SafeSense™ paper jam:
If the SafeSense™ feature activates (SafeSense™ light remains on) to cause the user
to think the shredder has jammed when it has not, use the
Override Switch
to deactivate the SafeSense™
feature and clear the paper.
Warning
– when switch is in override position, the SafeSense™ light will flash and
the SafeSense™ feature will NOT function. Once the paper is cleared, reset the SafeSense™ feature.
Feed into paper entry
and release
Press Auto-On ( )
Continuous operation:
4-5-minute maximum
NOTE:
Shredder runs briefly
after each pass to clear entry.
Continuous operation beyond
4-5-minutes will trigger
20-minute cool down period.
Press and hold
Reverse (R)