Filter
Top Products
3
OPERATION
This product features an auto-start sensor. This
sensor will turn on the cutting blades whenever
anything is inserted into the paper entry (while the power switch is in
the
AUTO
position). For the safety of pets and children, we recom-
mend always moving the power switch to
OFF
and unplugging when-
ever the shredder is unattended or not in use.
1. Assemble shredder head to basket (see “ASSEMBLY”).
2. Remove any large paper clips or other foreign objects (except sta-
ples and small paper clips) from paper. If folding paper to fit paper
entry, adjust sheet capacity appropriately.
Do not attempt to shred paper clips or other hard
materials (except staples and small paper clips)
with this machine. Extensive use of paper clips or other hard materials
will result in damage
to the cutting system and will void the manufacturer's warranty.
3. Be sure power switch is in the
OFF
(O) position. Plug shredder
into the proper power supply outlet.
4. Move power switch to
AUTO
(I) position. To clear the cutting
blades, the shredder will “run” for about 1 second immediately
after switching to
AUTO
(I). When the unit is turned on and in
standby mode (green LED lights), the shredder is ready to be fed
paper through the paper entry. (See “TROUBLESHOOTING” if red
LED is lit.)
NEVER insert hands or fingers into paper entry as
serious personal injury may result.
Do not exceed recommended sheet capacity (see
“Product Usage Guide” on page 1).
5. Slide paper straight into paper entry until the shredder auto-
matically begins shredding.
The shredder automatically stops when shredding is complete.
Continue shredding as desired to a MAXIMUM shredding time
of 10-12 minutes. At this time, the machine MUST be allowed
to “cool down” for a MINIMUM of 20 minutes. (See “Cool-
Down Cycle” section for more information.)
If the shredder jams or shuts off before the maximum shredding
time, see “Clearing a Jam” section for further instructions.
6. Move power switch to
OFF
(O) position when shredding is com-
plete.
7. Unplug power cord from outlet when shredder is unattended not in
use.
8. Look through viewer to see if basket is full. If full, lift off shredder
head and empty basket contents. Replace shredder head into posi-
tion on basket.
Cool-Down Cycle
This shredder is protected with a special safety feature which prevents
the motor from overheating with extensive use.
When shredding is
attempted beyond the machine's maximum running time, the
shredder will automatically shut off its motor until it has
cooled to an acceptable operating level.
This is normal and the
shredder will return to operation after the “cool-down” period. See
“Product Usage Guide” (page 1) for maximum running time and
related cooling or “off” time.
Clearing a Jam
If the shredder sheet capacity is exceeded or paper is not put in
straight, a jam may result. See “Product Usage Guide” (page 1) for
maximum sheet capacity for your shredder. In the case of a jam, the
shredder's red LED will light and the shredder will automatically stop
until the jam is cleared.
To clear a jam:
1. Move the power switch to the REVERSE (R) position. (If waste
basket is full, empty it before clearing jam.) The shredder will
reverse the paper to clear the jam.
2. If the shredder jams in reverse, move the power switch to AUTO
(I) and allow to run for about five seconds. If jam does not clear,
move power switch to REVERSE (R) again and allow to run for
about five seconds. Repeat this procedure until the jam is cleared.
If necessary, use care to grasp the paper carefully and pull out to
clear the jam.
3. Once the jam is cleared, move the power switch to AUTO (I) for
continued shredding or OFF (O) if shredding is complete.
MAINTENANCE
Confetti cut shredders (Model PS60C-2) require regular (monthly) oil-
ing of the cutting blades to maintain proper operation. Failure to oil
the blades regularly could result in reduced sheet capacity perform-
ance, excessive noise during operation, paper jams and possibly
shredder failure.
We recommend using only Powershred Lubricant #35250
(available by contacting Fellowes) or a vegetable-based oil
(such as corn or canola) in a non-aerosol container with an
extension nozzle.
Never use flammable synthetic oil, petroleum-
based, or aerosol lubricants to oil the cutting
blades. Some agents may combust, causing serious injury.
To oil the cutting blades:
1. From the top of the shredder, squeeze the recommended lubricant
across the full width of the blades.
2. Move the power switch to
AUTO
(I) position and allow the blades
to run at least 3 seconds.
3. Move the power switch to
REVERSE
(R) position and allow it to
run for at least 3 seconds.
4. Repeat steps 2-3 above at least 3 times.