Fellowes S40C-2 Paper Shredder User Manual


 
3
OPERATION
This product features an auto-start sensor. This
sensor will turn on the cutting blades whenever
anything is inserted into the paper entry (while the power switch is in
the
AUTO
(I) position). For the safety of pets and children, we rec-
ommend always moving the power switch to
OFF
(O) and unplugging
whenever the shredder is unattended or not in use.
1. Assemble shredder (see "ASSEMBLY").
2. Remove any paper clips or other foreign objects (except staples)
from paper. If folding paper to fit paper entry, adjust sheet capaci-
ty appropriately.
Do not attempt to shred paper clips or other hard
materials (except staples) with this machine.
Extensive use of paper clips or other hard materials will result in dam-
age to the cutting system and will void the manufacturer's warranty.
3. Be sure power switch is in
OFF
(O) position. Plug shredder into
proper power supply outlet.
4. Move power switch to
AUTO
(I) position. To clear the cutting
blades, the shredder will "run" for about 1 second immediately
after switching to
AUTO
(I). When the unit is turned on and in
standby mode, the shredder is ready to be fed paper through the
paper entry. (See “TROUBLESHOOTING” if red LED is lit.)
NEVER insert hands or fingers into
paper entry as serious personal injury may result.
Do not exceed recommended sheet capacity (see
"Product Usage Guide" on page 1).
5. Slide paper straight into paper entry until the shredder automati-
cally begins shredding.
The shredder automatically stops a few seconds after shredding is
complete.
Continue shredding as desired to a
MAXIMUM shredding time
of 5-7 minutes
. At this time, the machine MUST be allowed to
"cool down" for a MINIMUM of 15 minutes
. (See "Cool-
Down Cycle" for more information.)
If the shredder jams or shuts off before the maximum shredding
time, see "Clearing a Jam" section for further instructions.
6. Move power switch to
OFF
(O) position when shredding is com-
plete.
7. Unplug power cord from outlet whenever shredder is unattended
or not in use.
8. Look to see if basket is full. If full, lift off shredder head and
empty basket contents. Replace shredder head into position on
basket.
Cool-Down Cycle
This shredder is protected with a special safety feature which prevents
the motor from overheating with extensive use.
When shredding is
attempted beyond the machine's maximum running time, the
shredder will automatically shut off its motor until it has
cooled to an acceptable operating level.
This is normal and the
shredder will return to operation after the “cool-down” period. See
“Product Usage Guide” (page 1) for maximum running time and
related cooling or “off” time.
Clearing a Jam
If the shredder sheet capacity is exceeded or paper is not put in
straight, a jam may result. See “Product Usage Guide” (page 1) for
maximum sheet capacity for your shredder. In the case of a jam, the
machine will “bog down” and fail to shred the paper.
To clear a jam:
1. Move the power switch to the
REVERSE
(R) position. (If waste
basket is full, empty it before clearing jam.) The shredder will
reverse the paper to clear the jam.
2. If the shredder jams in reverse, move the power switch to
AUTO
(I) and allow to run for about five seconds. If jam does not clear,
move power switch to
REVERSE
(R) again and allow to run for
about five seconds. Repeat this procedure until the jam is cleared.
If necessary, use care to grasp the paper carefully and pull out to
clear the jam.
3. Once the jam is cleared, move the power switch to
AUTO
(I) for
continued shredding or
OFF
(O) if shredding is complete.
MAINTENANCE
Confetti cut shredders require regular (monthly) oiling of the cutting
blades to maintain proper operation. Failure to oil the blades regu-
larly could result in reduced sheet capacity performance, excessive
noise during operation, paper jams and possibly shredder failure.
We recommend using only Powershred Lubricant #35250
(available by contacting Fellowes) or a vegetable-based oil
(such as corn or canola) in a non-aerosol container with an
extension nozzle.
Never use flammable synthetic oil, petroleum-
based, or aerosol lubricants to oil the cutting
blades. Some agents may combust, causing serious injury.
To oil the cutting blades:
1. From the top of the shredder, squeeze the recommended lubricant
across the full width of the blades.
2. Move the power switch to
AUTO
(I) position and allow the blades
to run at least 3 seconds.
3. Move the power switch to
REVERSE
(R) position and allow it to
run for at least 3 seconds.
4. Repeat steps 2-3 above at least 3 times.
CAUTION
WARNING
CAUTION
WARNING
CAUTION