Fortinet 1000B Network Card User Manual


  Open as PDF
of 2
 
Port Information
Port 1 IP: ____.____.____.____
Netmask: ____.____.____.____
Port 2 IP: ____.____.____.____
Netmask: ____.____.____.____
Port 3 IP: ____.____.____.____
Netmask: ____.____.____.____
Port 4 IP: ____.____.____.____
Netmask: ____.____.____.____
The internal interface IP address and netmask must be valid for the internal network.
General settings
Administrator password:
Network Settings: Default Gateway:
____.____.____.____
Primary DNS Server: ____.____.____.____
Secondary DNS Server: ____.____.____.____
Factory default settings
NAT/Route mode Transparent mode
Port 1 interface 192.168.1.99 Management IP 0.0.0.0
Port 2 interface 0.0.0.0 Administrative account settings
Port 3 interface 0.0.0.0 User name admin
Port 4 interface 0.0.0.0 Password (none)
To reset the FortiAnalyzer unit to the factory defaults, in the CLI type the command
execute factory reset
Collecting Information
Conguring
Web-based Manager
Use the following procedure to connect to the web-based manager for the rst time. Congu-
ration changes made with the web-based manager are effective immediately without reset-
ting the FortiAnalyzer unit or interrupting service.
To connect to the web-based manager
Connect the Port 1 interface of the FortiAnalyzer unit to Ethernet port of the manage-
ment computer.
Use a cross-over Ethernet cable to connect the devices directly. Use straight-through
Ethernet cables to connect the devices through a hub or switch.
Congure the management computer to be on the same subnet as the FortiAnalyzer
Port 1 interface.
To do this, change the IP address of the management computer to 192.168.1.2 and the
netmask to 255.255.255.0.
To access the FortiAnalyzer web-based manager, in your browser, go to
https://192.168.1.99 (remember to include the “s” in https://).
Type admin in the Name eld and select Login.
After connecting to the Web-based manager, you can congure the FortiAnalyzer unit IP ad-
dress, DNS server IP address, and default gateway to connect the FortiAnalyzer unit to the
network.
To congure interfaces
Go to System > Network > Interface.
Select the edit icon for each interface to congure.
Set the IP address and netmask for the interface.
Select OK.
To congure the Primary and Secondary DNS server IP addresses
Go to System > Network > DNS, enter the Primary and Secondary DNS IP addresses
select Apply.
To congure a Default Gateway
Go to System > Network > Routing and select Create New.
Set Gateway to the Default Gateway IP address and select OK.
1.
2.
3.
4.
1.
2.
3.
4.
1.
1.
2.
Command Line Interface
The FortiAnalyzer-1000B has serial port. Use the null modem cable to connect it to your
management computer.
To connect to the FortiAnalyzer unit
Use a null modem cable to connect the FortiAnalyzer serial port to the management
computer serial port.
Start a terminal emulation program (such as HyperTerminal) on the management com-
puter. Use these settings: Baud Rate 9600, Data bits 8, Parity None, Stop bits 1, Flow
Control None.
At the login: prompt, type admin and press Enter twice.
(The login prompt is preceded by the server default host name.)
After connecting to the CLI, you can congure the FortiAnalyzer unit IP address, DNS server
IP address, and default gateway to connect the FortiAnalyzer unit to the network.
To congure the FortiAnalyzer unit using the CLI
Set the IP address and netmask of the Port1 interface.
cong system interface
edit port1
set ip <intf_ip>/<netmask_ip>
end
Congure the primary and secondary DNS server IP addresses.
cong system dns
set primary <dns-server_ip>
set secondary <dns-server_ip>
end
Congure the default gateway.
cong system route
edit 1
set device <interface>
set dst <destination_ip>
set gateway <gateway_ip>
end
1.
2.
3.
1.
3.
4.
Adding an administration password
By default, the admin user does not have a password. To restrict access to the FortiAnalyzer
unit management account, add password for the admin user account.
To add the admin user account password
Go to System > Admin.
For the admin user, select the Change Password icon.
Enter a new password in the New Password box.
Reenter the password to Conrm Password box.
Select OK.
1.
2.
3.
4.
5.
Adding an administration password using the CLI
To add an administration password in the CLI enter the following commands:
cong system admin
edit admin
set password <password>
end
Shutting down the FortiAnalyzer unit
When powering off the FortiAnalyzer unit, always shut down the unit using the following pro-
cedures before disconnecting the power supply. Not following this procedure can increase
the risk of damaging the FortiAnalyzer hard disk.
To power off the FortiAnalyzer unit
Go to System > Dashboard.
In the System Operation list, select Shut Down.
Select Go.
Once the indicates the shut down procedure has completed, disconnect the
FortiAnalyzer unit from the power source.
Shutting down the FortiAnalyzer unit using the CLI
Enter the following command at the prompt:
execute shutdown
1.
2.
3.
4.
 previous