Filter
Top Products
4. To punch, press the PUNCH ~button (02). The Oocu-
Bind P300 punches up to 15 sheets of 20 Ib./80 gram
paper at once. Punch only TWO clear covers at a time to
prevent jams and excessive wear.
5. If punch jams, depress the RESET~button (03). Then
press the PUNCH ~button (02) again and remove paper
or covers from punch throat (it may be necessary to punch
several times in order to remove the paper). Repeat steps 1
to 4 with slightly less paper to avoid punch jams on addi-
tionallifts.
Thank you for purchasing the GBC OocuBind P300. This system
features our new exclusive Radiaf Bind design. This design
enables you to assemble your document as you punch. making
it easier to load paper onto the binding comb than previous
systems! The OocuBind P300 advanced punching technology
also makes it easier to punch more paper at once while
providing greater reliability.
A. GmlNG STARTED
1. Firmly push the female end of the power cord into the
power cord receptacle (A) located on the back of the
machine (see figure 1 ).
h CAUTION: Make sure this step is complete prior to
~ plugging the male end ot the power cord into a power
receptacle .
2 Plug the male end of the power cord into an appropriate
power receptacle.
B. DETERMINE SHEET WIDTH
1. Set Edge Guide (8) to paper size you wish to bind (11",
8-1/2" letter size, 11-1/4" oversized cover, A4 ring, AS,
Japan A4) (see figure 1). When using oversized covers, set
the Edge Guide on Covers, punch all of the covers for your
job and set aside. Move the Edge Guide back to the 11"
setting to punch your contents then bind.
C. DETERMINE PLASTIC CDMB SIZE
1 Slide the Binder Sizer open (C) (see figure 1 ).
2. Place document including covers behind Binder Sizer.
3. Release the Binder Sizer and select the comb binding
element that corresponds with the size shown by guide.
Only comb sizes up to 1" (25 mm) are shown. Your
DocuBind can bind documents up to 425 sheets, or 2"
(50 mm) comb size. For best results, always use GBC
brand covers with GBC color-coordinated binding combs.
E. BINDING
1. Place a Plastic Comb Binding Element behind the Vertical
Comb (E) with the open portion of element facing you (see
figure 3).
2. Rotate the Bind Lever up (E1) toward you until the Comb
Binding Element (E2) opens sufficiently to insert your
document (see figure 4).
3. Thread front cover finished .side facing down (see figure 5),
onto open Binding Element Fingers (E3). Thread pages,
front facing down, onto element. Repeat for large docu-
ments as required. Place the back cover, finished side
facing upward on open Binding Element Fingers last.
4. Push the Bind Lever away from you back to its original
position to close the binding element.
5. Remove book by lifting upward. Your presentation is
now complete!
6. Once you become familiar with your DocuBind P300,
you will find that you can bind as you punch, increasing
your productivity.
F. EMPTY CHIP DRAWER
1. Empty Chip Drawer (F) after repeated use. Pull drawer
gently toward you to open. When putting back in, the
drawer will snap into place (see figure 6).
D. PUNCHING PAPER (see figure 2)
1 Lift the Wire Paper Suppor1 (D) into place (optional).
2. Align sheets or covers and inser1 edge to be bound into
punch throat (D1 ).
3. Jog the sheets until they are flush against the edge guide
and the bottom of the punch throat. Allow the paper to rest
against the Wire Paper SUppOr1. or, you may
prefer to hold the sheets in place with one hand.
G. SERVICE
Should your DocuBind require service contact GBC at'
Quartet/GBC
5700 Old Orchard Road
Skokie, IL 60077 USA
1-800-541-0094
http://www.gbc.com/opd
SPECIFICATIONS
Dimensions'
Bind Capacity"
Weight:
Electrical Power'
Maximum Sheet Width'
Dis-engagable Pins"
18" (W) x 81/2" (H) x 16" (0)
457mm x 216mm x 406mm
341bs. (15.2 kg.)
115V AC, 60Hz, 2.3 amps, 130
watts or 230V AC, 50Hz,
1.3 amps
15 sheets of 20 Ib. paper
15 sheets of 80 glm2 paper
425 sheets or 2"
(50mm)
11.7" (297mm A4)
1 (A5 paper) within comb
storage bin
Punch Capacity"
5