Filter
Top Products
1312
98
1514
1110
PC04
PC07
PC06
TIME PROJECTION
The Sport Alarm Clock can project the time display for a
short period when operating on batteries, or continuously
when using the AC/DC adapter. The clock is designed to
project the time image on the ceiling in red, no focusing
is required.
NOTE: Time display on the ceiling and the time on
the LCD display cannot be viewed simultaneously, as
their viewing directions are opposite. Place the unit at
the head of your bed to view the projected image
correctly.
CURRENT TIME PROJECTION
Press "LIGHT/SNOOZE" button to turn on the LCD
backlight and project the time display onto the wall or
the ceiling for 3 seconds.
CONTINUOUS TIME PROJECTION
Connect AC/DC adapter (optional) to project the time
display continuously.
CALENDAR AND CLOCK DISPLAY MODES
The Alarm Clock has a three (3) display modes:
TIME, DATE and ALARM
The current time is displayed in hour-minutes format
which is the default display mode. The date is displayed
in month-date format.
The alarm time is displayed in hour-minutes format.
ALARM
If the alarm is activated, it will sound at the set time and
the (bell icon) will flash.
To review the alarm time, press MODE button once in
TIME display and the default alarm time will be
displayed as “1:00” and “ALARM” will be displayed in
the top left of the LCD display.
To review the date, press MODE button when the
ALARM TIME is displayed.
When MODE is pressed again the seconds will be
displayed.
To return to the TIME display, press MODE button
again or wait for it to change back.
TO SET ALARM TIME
Press SET button twice in TIME
display. If the alarm is being set for
the first time, “1:A” will be displayed
with flashing, and “ALARM” will
display in the top left.
Press MODE button to adjust the
desired alarm HOUR.
Press SET button to set the desired
alarm MINUTES, the alarm minutes
“00”will flash.
Press MODE button to adjust the
desired alarm minutes.
Press SET button again to confirm set alarm time.
The clock will return to the TIME display mode.
ENABLE OR DISABLE ALARMAND CHIME
• Press SET button in TIME display mode. Alarm hour
and minute digits will flash.
• Press MODE button to enable or disable the alarm and
chime in the following sequence:
ALARM ON-
ALARM&CHIMEON-
CHIME ON-
ALARM&CHIME OFF -
ALARM ON-
• Press SET button to confirm the
alarm and chime status. Clock will
go into TIME and DATE set mode. Wait and clock will
return to TIME display mode.
PRECAUTIONS
This product is engineered to give you years of
satisfactory service if handled carefully.
Here are a few precautions:
1. Do not immerse the unit in water.
2. Do not clean the unit with abrasive or corrosive
materials. They may scratch the plastic parts and
corrode the electronic circuits.
3. Do not subject the product to excessive force, shock,
dust, temperature, or humidity, which may result in
malfunctions, shorter lifespan, damaged batteries,
and damaged parts.
4. Do not tamper with the unit's internal components.
Doing so will invalidate the warranty and may cause
damage. This unit contains no user-serviceable parts.
5. Use only fresh batteries. Do not mix new and old
batteries.
6. Read the user's manual thoroughly before operating
the unit.
SPECIFICATIONS
Projection
Current time display projected onto the ceiling or wall
Fixed red display projection
Calendar and Clock
12/24 hour display in hh : mm format
Date Format: Month - Day format
Single 2-minute crescendo alarm with snooze and chime
LED backlight
Power
2AAA batteries (not included)
AC/DCAdapter (3V, 100mA),
center pin positive (optional)
Dimensions
4.33 (L) x 4.72 (H) x 4.33 (D) inches
SETTING THE CLOCK
TIME AND DATE
After batteries are installed as shown inside the battery
compartment, the default time will be displayed as “1:00”
To set current date and time:
1). Press SET button 4 times, and the
MONTH will be displayed as “1”.
2). Press MODE button to set the
current month.
3). Press SET button and the DAY
will be displayed.
4). Press MODE button to set the
current day.
5). Press SET button again and the
HOUR will be displayed as 1: A.
6). Press MODE button to set current
hour (AM, 24 hour, PM).
7). Press SET button and the
MINUTES will be displayed.
8). Press MODE button to set the
correct minute.
9). Press SET button to complete setting the month,
date, hour and minute.
10).Press MODE button to return clock to normal
operation.
24 HOUR TIME FORMAT
Press MODE button until the desired hour in “24 hour”
format is shown. To return to “12 hour” format continue
pressing MODE.
TO STOPALARM
To stop the alarm for 24 hours, press SET when alarm
is activated.
To stop alarm for 5 minutes, press SNOOZE/LIGHT
button
If no button is pressed, alarm will stop in 2 minutes.
Press MODE button to disable the alarm in ALARM
display format while alarm time digits are flashing.
(The bell icon will disappear from the display when
alarm is disabled).
CHIME
When CHIME is activated, it will sound at every hour.
STANDARDWARRANTY INFORMATION
This product is warranted from the manufacturing defects
for one year from date of retail purchase. It does not
cover damages or wear resulting from accident, misuse,
abuse, commercial use, or unauthorized adjustment and/
or repair.
Note that online product registration is required to ensure
valid warranty protection.
To register your product, go to our Company website at:
www.digiviewtime.us. Click Online Product Registration
under the Customer Service menu.
Should you require assistance with this product and its
operation, please contact our Customer Service Hotline
1(866) 443 3543
Please direct all returns to the place of the original
purchase. Should this not be possible, contact Customer
Service Hotline for assistance and to obtain a Return
MerchandiseAuthorization (RMA). Returns without a
return authorization will be refused. Please retain your
original receipt as you may be asked to provide a copy
for proof of purchase.
Hideki Electronics, Inc. reserves the right to repair or
replace the product at our option.