Intelligent Motion Systems IB462He Webcam User Manual


 
Minimum Required Connections
IB462He Mechanical Specifications
Dimensions in Inches (mm)
For More Information:
See the complete IB462He Product Manual
on the IMS Product CD or at www.imshome.com
Direction Input
Current Adjustment
Voltage (0 - 1.0V)
Step Clock Input
Phase A
Phase B
Phase B
Phase A
150µF for each Amp Peak
Ouput Current - 60V Electrolytic
+5V
22µF 10V
Tantalum
MOTOR
SUPPLY
LOGIC
SUPPLY
+V
GND
GND
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
01µF
100V
The Product Manual
The IB462He Product Manual contains full details about the product and associated
Interface Boards, the INT-462 and the OSC-462H, and should be referenced prior
to product use. These are available on the CD which shipped with your product and
from the IMS web site at http://www.imshome.com.
Notes and Warnings
intelligent motion systems, INC.
Excellence in Motion
370 N. MAIN ST., PO BOX 457, MARLBOROUGH, CT 06447
PH: (860) 295-6102, FAX: (860) 295-6107
Internet: www.imshome.com, E-Mail: info@imshome.com
Q U I C K R E F E R E N C E
462
IB
He
ULTRAMINIATURE BIPOLAR
STEPPING MOTOR DRIVER
The IB462He, INT-462 and OSC-
426H are sensitive to Electrostatic
Discharge (ESD).
Hazardous Voltage Levels may
be present if using an open
frame power supply to power the
IB462He, INT-462 or OSC-462H.
The Power Supply output voltage
must not exceed the maximum
input voltage of the IB462He,INT-
462 or OSC-462H.
Do not apply power to the IB462He
without proper heat sinking or
cooling. The max. rear plate
temperature is 70°C!
The rear mounting surface of the
driver contains various voltages and
must be kept isolated when attached
to a conductive surface!
Do not "Hot Plug" Power or Motor
Connection while power is applied
to any of the IB462He drivers or
accesories.
General Specifications
Electrical Specifications Condition Min Typ Max Unit
Input Voltage Range +12 +48 VDC
Phase Output Current Per Phase 0.1 2 A
Quiescent Current (+V) Outputs Floating 4 mA
Quiescent Current (+5V Input) Outputs Floating 50 80 mA
Current Adjust Input Voltage 1.0 VDC
Logic Specifications Condition Min Typ Max Unit
Low-Level Input Voltage SCLK, DIR, H/F, Reset 0.6 VDC
Low-Level Input Voltage Enable Input 1.3 VDC
High-Level Input Voltage All Inputs 2 5 VDC
Low-Level Input Current SCLK, DIR, H/F, Enable -1.2 mA
Low-Level Input Current Reset Input Only -200 µA
High Level Input Current SCLK, DIR, H/F, Enable 10 µA
Input Pull-up Resistance SCLK, DIR, H/F, Enable 4.5 4.7 4.9 k
Input Pull-up Resistance Reset Input Only 50 51 52 k
Thermal Specifications Min Typ Max Unit
Ambient Temperature 0 +50 °C
Storage Temperature -40 +125 °C
Plate Temperature (Add't Cooling Req'd) +70 °C
1.895
(48.13)
2.120
(58.85)
0.585
(14.86)
1.169
(29.7)
21 X 0.020 (0.5)
SQ. PIN
0.79
(2.0)
0.270
(6.86)
2X Ø 0.150
(3.81)
2X R 0.125
(3.18)
0.284
(7.21)
0.065
(1.65)
0.189
(4.8)
IB462He, INT-462 and OSC-462H Quick Reference R010708
IB462He Mounting Requirements
The IB462H is designed to be socketed or soldered into a PCB. For PCB layout
information and circuit board hole pattern please refer to the IB462He Manual,
Section 1.7. This part of the Quick Reference only supplies Mechanical Mounting
information.
Heat sinking and the use of the included insulating thermal pad are ABSOLUTELY
REQUIRED for the IB462He driver at all power levels. Below are some examples of
mounting configurations.
H-462H Heat Sink Kit Information
IB462He Pin Configuration
Pin # Function Pin # Function
1 Phase Current Adjustment 11
Phase B Step Motor Output
2 Reset Input 12
3 Half/Full Step Input 13
+12 to +48 VDC Motor Power
Supply Input
4 Step Clock Input 14
5 +5 VDC Logic Supply Input 15
Power Supply Return (Ground)
6 CW/CCW Direction Input 16
7 Phase Enable Input 17
Phase A Step Motor Output
8 Phase B Current Sense Input 18
9
Phase B Step Motor Output
19
Phase A Step Motor Output
10 20
21 Phase A Current Sense Input
.708
(17.98)
0.553
(14.04)
1.560
(39.62)
0.090
(2.29)
2X Ø 0.120
(3.05) THRU
2.120
(53.85)
2.665
(67.69)
0.273
(6.93)
0.585
(14.86)
1.169
(29.69)
Heat Sink Kit Contents
Vertical PCB Mounting
Heat Sink Dimensions
PCB Mounting Using Right-Angle Receptacle
1 - H-462 Heat Sink
2 - 4-40 x 1.375 Scew
2 - 6-32 x 5/8 Screw
2 - Spacers
2 - #4 Split Washers
2 - #6 Flat Washers
2 - #6 Split Washers
Spacer
(KF2-440)
D
D
I
B462He
TI-462H Isolating
Ther mal Pad (Included)
H-462 Heat Si nk
PCB
#6- 32 Threaded
A
A
B
B
E
E
C
C
H-462 Heat Sink
#6-32
Threaded
A
B
C
Spacer
(Not Supplied)
HY462-CN021
Right Angle Adapter
(Receptacle)
TI-462H Isolating
Thermal Pad (Included)
I B462He Driver
User PCB