Filter
Top Products
15
ENGLISH
SCOPE SETTING*
1
Settings for the wave form monitor and vector scope
Item To do Setting value
GAIN
Adjust the gain level for the incoming wave form data. –10 – +10
SIZE*
2
Select the size of the wave form monitor and vector scope window. NORMAL, LARGE
POSITION*
2
Select the position of the wave form monitor and vector scope
window.
1 (lower right), 2
(lower left), 3 (upper
left), 4 (upper right)
TRANSPARENT
Activates/deactivates the function to make the window translucent.
ON (translucent),
OFF (normal)
AUTO OFF
Activates/deactivates the function to make the wave form monitor and
vector scope window go off automatically 15 minutes after displaying it.
ON, OFF
WAVE DISPLAY
Select the wave form for the wave form monitor. Y/Pb/Pr (HD signals)
Y/Cb/Cr (SD signals)
R/G/B (RGB signals)
WAVE FILTER
Activates/deactivates the low-pass filter for the incoming wave form
data.
FLAT (no filter),
LOWPASS
WAVE OVER
LEVEL
Adjust the over level for the incoming luminance (Y) and RGB
signals.
☞ “NOTE”
MARKING
Activates/deactivates the function to change the color of a wave form
when the signal exceeds the limit specified on “LEVEL” (☞ below).
OFF, ON
LEVEL
Adjust the lower limit for the over level. 070 – 109
*
1
Wave form monitor does not work for DVI signals (PC input).
Vector scope does not work for RGB signals.
*
2
When you set “SIZE” to “LARGE,” the window is displayed in the center of the screen regardress of the “POSITION”
setting.
SYNC FUNCTION
Settings for the synchronization with signals
Item To do Setting value
NO SYNC ACTION
Select the screen status when no signal is coming in. OFF, P.SAVE (power save
mode), GRAY B. (gray screen)
DELAY TIME
Select the period until the screen status changes as selected
in “NO SYNC ACTION” after signals stop coming in.
30sec., 5min., 15min.
SYNC INPUT
SEL.*
3
Select the sync signal for the VIDEO1, VIDEO2 and
COMPO./RGB input.
INT. (Internal sync),
EXT. (External sync)
LOW LATENCY
Activates/deactivates the function to shorten the time
taken to display the picture (low latency function).
• If the picture is not displayed steadily while “ON” is
selected, select “OFF.”
• While “ON” is selected, the displayed picture may
become unstable when an operation using buttons on
the front panel or the menu is performed, or when the
signal format changes.
ON, OFF
• When setting “NO SYNC ACTION” to “GRAY B.,” the screen color changes to gray and the power consumption
of the back light is saved by half. Selecting “P.SAVE” (power save mode) saves more power consumption by
turning off the back light.
*
3
Memorized for each input.
Operation guide
Shows the buttons for each
operation.
Example of the vector scope
Ex.: When the color bar is displayed
NOTE
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
Example of the wave form monitor
Ex.: When the luminance signal is Y, “MARKING” is set to “ON”
and “LEVEL” is set to “080”
• The wave which goes over the value set on “LEVEL” is
indicated in red.
• The display differs depending on the input signal or the
setting of “WAVE DISPLAY.”
Y
Video signal
EndStart
Red White
DT-V24G1_20L3G_EN.indd 15DT-V24G1_20L3G_EN.indd 15 10.1.15 3:22:22 PM10.1.15 3:22:22 PM