Kodak 2610 Printer User Manual


  Open as PDF
of 2
 
VI. System/Software Setup
Refer to the Matchprint ProofPro or the DirectWorks Suite User’s Guide for the following procedures:
Reference Profile: = US_Web_SWOP.icc
Paper Profile in MPPP RIP v1.0: = MPPP2610_600x600_MPDye_MPPPDyePub_v1r1.icc
Paper Profile in MPPP RIP v2.0: = K_13_5533_0N003_031_XRD41_1.icc
Set Kodak Polychrome Graphics CFM to Rendering Intent: = Perceptual, Black Generation: = Retain Integrity if CMYK to CMYK is left
unchecked, use GCR , Total ink: = 310, Black Ink Limit: = 100, Black Generation: = Medium.
Calibrate the KPG Matchprint ProofPro 2610 inkjet printer for use with Matchprint ProofPro Inkjet Media Publication/Dye paper utilizing the file:
In MPPP RIP v1.0: = MPPP2610_600x600_MPDye_MPPPDyePub_v1r1.bpl
In MPPP RIP v2.0: = K_13_5533_0N003_031_XRD41_1.epl
VII. Finished Proof Characteristics
A properly made proof using the Matchprint ProofPro 2610 inkjet printer with Matchprint ProofPro RIP or DirectWorks Suite, printed on
Matchprint ProofPro Inkjet Media Publication/Dye should have the following color characteristics:
Color
Density
Absolute
Density
Hi-Lo Ink
References
TVI @ 50%
(Dot Gain)
(± 3)
Print Contrast@
75% Tone
( ± 3)
Color (per CGATS.5)*
L* C* h(ab)*
(± 3) (± 3) ( ± 3)
Yellow .89(± 0.05) 0.90 – 1.05 17 24 83.92 75.15 92.27
Magenta 1.32(± 0.05) 1.30 – 1.46 21 32 47.10 67.97 355.56
Cyan 1.29(±0.05) 1.22 – 1.36 24 27 56.64 55.69 225.51
Black 1.73((± 0.06) 1.53 – 1.68 24 40 14.80 4.49 -
Red 46.58 76.52 34.12
Green 52.28 67.25 159.47
Blue 21.65 58.68 307.40
Background Density (+/-0.02): D
c
= 0.11 D
m
= 0.12 D
y
= 0.15
*CIELCh values represent measurements at target density.
Note: All measurements were made using a calibrated Gretag™ SPM50 spectrophotometer (D50 illuminant, 2° observer, non-polarized).
The density (Status T) and colorimetric values are absolute, base included, measured over a black backup. TVI’s were calculated using the
Murray-Davies equation (CGATS.4). All tolerances reflect normal systems variability and assume the use of a calibrated measurement
device.
To establish comparison values for finished proofs and determine any offset in instrumentation used, measure each pair of ink reference
patches from a current SWOP Ink Hi-Lo Color Reference. Compare them to the values shown in the table above for each color. The SWOP
Hi-Lo Color Reference used to calculate the offset values had a December 2002 expiration date.
VIII. Sample Proofs
Kodak Polychrome Graphics has supplied two proofs that conform to this Application Data Sheet to SWOP
for their analysis and retention.
CALL TOLL-FREE 1-877-KPGraphics (1-877-574-7274) FOR ADDITIONAL INFORMATION
OR VISIT US ON THE WEB AT www.kpgraphics.com
© 2005 Eastman Kodak Company. All rights reserved. Kodak, Matchprint and ProofPro are
trademarks of Eastman Kodak Company. All trademarks and registered trademarks used
herein are the property of their respective owners.
ADS 0024-050504
 previous