Filter
Top Products
Installation
Operating Environment
This switch must be installed and operated within the limits
of the specified operating temperature and humidity (see the
Specifications section)
Do not place objects on top of the unit. Do not obstruct any
vents on the unit
Do not position the switch in direct exposure to the sun, or
near any heat source such as a heater, radiator etc.
Prevent water and moisture entering the unit. If necessary,
use a dehumidifier to reduce humidity.
Connecting Network Devices
1. This switch features Auto MDI/MDI-X RJ45 ports for easy
connection to other network devices using straight-through
type network patch cable, cross over cables are not
required.
2. The network patch cables must comply with the Category 5
standard or higher for 10 and 100Mbps data transmission,
and at least Category 5e for 1000Mbps transmission.
3. Please be aware that the maximum length of any Ethernet
segment is 100m. If you are connecting the switch to a
patch panel, a maximum 5m of cable should be used to
connect the switch to the panel; similarly any equipment
connected to the switch should also use a maximum of 5m
cable, per device. Installation cabling may use the
remaining length. Using higher specification network cable
may increase this to a certain extent.
4. Connect the power adapter to the mains and to the power
socket on the switch.
Troubleshooting
The power LED is not lit
Check the power adapter is properly connected to both the
mains outlet and the switch and that the power at the mains
socket is switched on!
The 1000M Link LED is not lit when connected to a
1000Mbps device
Check the network cable. Make sure it is properly
connected to the switch and to the network device. The
segment length must be below 100 metres (see remark in
Installation) and all cables and connectors in between must
be at least category 5e compliant. We recommend the use
of professionally manufactured cables with this product to
ensure full Gigabit compatibility (Cables which are self-
made may be non-compliant with Gigabit specifications
and requirements!)
Should problems persist connect a local 1000Base-T device
to check that the port is working correctly. If this works
correctly it is probable that the network segment you want to
use contains equipment which is not 1000Base-T compliant.
Check the network segment and replace non-complaint
equipment with higher specification cables and connectors
where required.
If you experience any other problems with the switch please
contact your supplier or LINDY.
WEEE , Recycling of Electronic Products
Europe
In 2006 the European Union introduced
regulations (WEEE) for the collection and
recycling of all waste electrical and electronic
equipment. It is no longer allowable to simply
throw away electrical and electronic equipment.
Instead, these products must enter the recycling process.
Each individual EU member state has implemented the WEEE
regulations into national law in slightly different ways. Please
follow your national law when you want to dispose of any
electrical or electronic products. More details can be obtained
from your national WEEE recycling agency.
Germany / Deutschland
Die Europäische Union hat mit der WEEE Direktive umfassende
Regelungen für die Verschrottung und das Recycling von
Elektro- und Elektronikprodukten geschaffen. Diese wurden von
der Bundesregierung im Elektro- und Elektronikgerätegesetz –
ElektroG in deutsches Recht umgesetzt. Dieses Gesetz
verbietet vom 24.März 2006 an das Entsorgen von Elektro- und
Elektronikgeräten über die Hausmülltonne! Diese Geräte
müssen den lokalen Sammelsystemen bzw. örtlichen
Sammelstellen zugeführt werden! Dort werden sie kostenlos
entgegen genommen. Die Kosten für den weiteren
Recyclingprozess übernimmt die Gesamtheit der
Gerätehersteller.
Radio Frequency Energy, Certifications
FCC Warning
This Equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including
interference that may cause undesired operation.
LINDY No. 25044
1
st
Edition NOV 2007
For Commercial Use only!
Tested to Comply with FCC Standards
www.lindy.com