Filter
Top Products
D1
c In the Primary and Secondary
DNS fields, enter the DNS
address(es) provided by your
ISP. You need to enter at least
one DNS address.
d Click the Save Settings button,
and go to Step E.
3 PPPoE
a If your ISP says that you are
connecting through PPPoE or if
you normally enter a user
name and password to access
the Internet, then select PPPoE
as the Internet Connection
Type.
b Enter the User Name and Pass-
word provided by your ISP. (Also
enter the Service Name, if
required.)
c Click the Save Settings button.
d Click the Status tab, and then
click the Connect button to
start the connection.
e Go to Step E.
4 RAS
RAS is a service used in Singapore
only. If you are using a RAS connec-
tion, check with your ISP for the nec-
essary setup information. When you
are finished, go to Step E.
D In its drop-down menu, the
Internet Connection Type set-
ting features six Internet con-
nection types: obtain an IP
automatically (DHCP), Static IP,
PPPoE, RAS, PPTP, and Heart
Beat Signal. Depending on
which connection type you
select, the features available
on the Basic Setup screen will
differ. Proceed to the instruc-
tions for the connection type
you are using.
1 Obtain an IP Automatically
(DHCP)
a If your ISP says that you are
connecting through DHCP or a
dynamic IP address from your
ISP, then select Obtain an IP
automatically as the Internet
Connection Type.
b Click the Save Settings button,
and go to Step E.
2 Static IP
a If your ISP says that you are
connecting through a static or
fixed IP address from your ISP,
then select Static IP as the
Internet Connection Type.
b Enter the IP Address, Subnet
Mask and Gateway Address
provided by your ISP.
I To test the Router’s settings,
open your web browser from
any computer. In the browser’s
Address field, enter
www.linksys.com/registration
and press the Enter key.
Congratulations! The installation of
the Router is complete.
5PPTP
PPTP is a service used in Europe and
Israel only. If you are using a PPTP
connection, check with your ISP for
the necessary setup information.
When you are finished, go to Step E.
6 Heart Beat Signal
Heart Beat Signal is a service used in
Australia only. If you are using a Heart
Beat Signal connection, check with
your ISP for the necessary setup infor-
mation. When you are finished, go to
Step E.
E Depending on the setup infor-
mation from your ISP, you may
need to provide a host name
and domain name for the
Router. The Host Name and
Domain Name fields are usu-
ally left blank. If requested by
your ISP (usually cable ISPs),
complete these two fields.
F If you haven’t already done so,
click the Save Settings button.
Then close the web browser.
G Power your cable or DSL
modem off and back on
again.
H Restart or power on your PCs so
they can obtain the Router’s
new settings.
BEFVP41_V2-QI-31212B JL
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2003
Cisco Systems, Inc. All rights reserved.
D2
D3
D4
D5
D6
I
For additional information or troubleshooting
help, refer to the User Guide on the Setup CD-
ROM. You can also call or e-mail for further
support.
24-hour Technical Support
800-326-7114
(toll-free from US or Canada)
E-mail Support
support@linksys.com
Website
http://www.linksys.com or
http://support.linksys.com
RMA (Return Merchandise Authorization)
http://www.linksys.com/support
FTP Site
ftp://ftp.linksys.com
Sales Information
800-546-5797 (800-LINKSYS)