Filter
Top Products
3
6) Keystone commands (Not executable in stand-by mode. Possible only to read during muting.)
The keystone commands are used for the keystone setting of this projector with the value. The value will vary
depending on the installation conditions, etc.)
ITEM ASCII HEX VALUE
KEYSTONE(vertical) KS 4Bh 53h ±20
How to set the value
Use the ASCII or HEX code as shown below to set the value.
ASCII '+' '–' '0' '1' '2' '3' '4' '5' '6' '7' '8' '9'
HEX 2Bh 2Dh 30h 31h 32h 33h 34h 35h 36h 37h 38h 39h
Sending commands Status code from Description
from the PC, etc. the projector
30 30 72 35 34 0D Command operating the same
'0' '0' 'r' '5' '4' ' ' as the MENU button
30 30 72 35 34 0D Command receipt confirmation
'0' '0' 'r' '5' '4' ' ' (Command echo back)
[Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII
codes.):
Button's name on remote
ASCII HEX
+ VOLUME r06 72h 30h 36h
– VOLUME r07 72h 30h 37h
KEYSTONE r43 72h 34h 33h
MAGNIFY r02 72h 30h 32h
AV MUTE ra6 72h 61h 36h
▲ r53 72h 35h 33h
▼ r2b 72h 32h 62h
t r4f 72h 34h 66h
s r59 72h 35h 39h
MENU r54 72h 35h 34h
ENTER r10 72h 31h 30h
AUTO POSITION r09 72h 30h 39h
FREEZE ra4 72h 61h 34h
ASPECT re2 72h 65h 32h
8) Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash
screen is being displayed, the splash screen is only canceled.)
Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes.
9) Password lock commands
The password lock commands control the password lock. The password lock enabling or disabling command is sent
with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password
lock is enabled or disabled successfully, the projector sends a return command comprising the data code,
password, and “1” at the end. When enabling or disabling the password lock fails, it sends a return command with
“0” at the end. There is no reconfirmation of the password. The password input command is for enabling projection
of image when password lock has been set to DISPLAY INPUT. The password input command is sent with a 4 to 8-
digit password comprised of any figures 1 to 4 at the end.
ITEM ASCII HEX VALUE
Password lock PSLOCK 50h 53h 4Ch 4Fh 43h 4Bh 0**** (Disabling), 1**** (DISPLAY INPUT),
enabling/disabling
2**** (MENU ACCESS), 3**** (SPLASH ID SCREEN)
Password input PASS 50h 41h 53h 53h ****
**** is a 4 to 8-digit password comprised of any figures 1 to 4.
7) Mute commands (Not executable in stand-by mode. When the mute commands are sent while the splash screen
is being displayed, the splash screen is only canceled.)
The mute commands are used for the mute setting of this projector with the 0 (30h) and 1 (31h).
ITEM ASCII HEX VALUE
MUTE MUTE 4Dh 55h 54h 45h
0 (OFF), 1 (ON)